Pulling out Fence Post

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

adrianp89

Senior Member
Joined
Sep 3, 2015
Posts
3,175
Reaction score
1,273
Location
Tampa Bay, FL
Ram Year
2019
Engine
Hemi 5.7
Hey guys, I have a metal fence post that is cementer into the ground that I need to remove... can I use the truck's tow hooks to yank it out (with straps of course) ? Or should I play it safe and just dig it out.... trying to save myself from doing extra in this FL sun.
 

Kenneth1977

Senior Member
Joined
Jul 20, 2015
Posts
131
Reaction score
29
Ram Year
2016 Limited 4x4
Engine
5.7
Just give it all the skinny pedal
More than likely it will just snap off at the bottom
 

Phylodog

Senior Member
Supporting Member
Joined
Aug 9, 2013
Posts
675
Reaction score
314
Location
Arcadia, IN
Ram Year
2012 & 2018
Engine
5.7 Hemi & 6.7L CTD
I'd buy a Hi-Lift jack and go that route long before taking a chance of the post (or part of it) flying into my truck. If the cement isn't right at the surface and you don't need to put something in its place I'd dig below grade, cut the post off and leave the cement there.
 

NewBlackDak

Senior Member
Joined
Feb 9, 2014
Posts
1,083
Reaction score
654
Ram Year
2014
Engine
Hemi 6.4L
I've pulled plenty of posts and stumps, but I normally use a hitch d-ring:shackle. No idea what the tow hooks are rated for.


Sent from my iPhone using Tapatalk
 

WilliamS

Senior Member
Joined
May 3, 2016
Posts
2,638
Reaction score
1,191
Location
Tampa FL
Ram Year
2014
Engine
Hemi 5.7
The tow hooks will pull it, the problem is where does the pole go when it breaks free?
 

DannyMK2

Senior Member
Joined
Mar 25, 2013
Posts
1,727
Reaction score
491
Location
Long Island, NY
Ram Year
2015 Power Wagon
Engine
6.4 Hemi
its easier to dig it out by hand. chances are using the truck is just going to bend the pole, rather then take it out all the way. once you dig around, give the pole a few wacks with a sledge hammer. it usually breaks the concrete free around the pole and you can wiggle it out.
 

Farmer Fran

Senior Member
Joined
Jul 28, 2013
Posts
1,508
Reaction score
1,294
Location
Earth
Ram Year
2020 Limited Loaded - Sold
I dig then pull the weight up with the truck.
 

Wise

Member
Joined
Feb 18, 2017
Posts
79
Reaction score
28
Location
Harrison, Ohio
Ram Year
2016
Engine
Hemi
I've used and old wheel to pull them worked out great especially if they are cemented in
 

Wise

Member
Joined
Feb 18, 2017
Posts
79
Reaction score
28
Location
Harrison, Ohio
Ram Year
2016
Engine
Hemi
A general idea I've just wrapped the chain at the bottom, never had a problem with it slidding up. It'll pull the post up instead of from the side just put a rock in front of it.
 

Attachments

  • images.jpg
    images.jpg
    9.6 KB · Views: 181

Devin1349

Senior Member
Joined
Aug 31, 2016
Posts
936
Reaction score
295
Ram Year
2011
Engine
Hemi 5.7
how deep is the cement???
 
OP
OP
A

adrianp89

Senior Member
Joined
Sep 3, 2015
Posts
3,175
Reaction score
1,273
Location
Tampa Bay, FL
Ram Year
2019
Engine
Hemi 5.7
No idea on depth - I assumed put the truck in 4Hi and pull slowly so it doesn't fly at me lol.
 

Ratket

Senior Member
Joined
Jul 14, 2014
Posts
3,571
Reaction score
1,300
Location
Arizona-
Ram Year
2018 1500
Engine
Hemi 5.7
Use 4low and let it walk- slow is the key- if u have to jerk it dont- That's when u get into " flying debris" territory
 

UnsatFC

Active duty NAVY
Military
Joined
Feb 16, 2017
Posts
1,279
Reaction score
653
Location
New Jersey
Ram Year
2015
Engine
5.7
I agree, 4low and walk....unless you want a new tailgate or rear window....I have seen neighbors do exactly that.


Use 4low and let it walk- slow is the key- if u have to jerk it dont- That's when u get into " flying debris" territory
 

Skubasteve!

Senior Member
Joined
Jun 18, 2017
Posts
377
Reaction score
197
Ram Year
2015
Engine
5.7
A general idea I've just wrapped the chain at the bottom, never had a problem with it slidding up. It'll pull the post up instead of from the side just put a rock in front of it.

Fantastic idea.
 

14hemiexpress

Senior Member
Joined
Mar 30, 2014
Posts
3,654
Reaction score
1,197
Location
Texas
Ram Year
2019
Engine
6.4l
4lo and rock it nice and slow. Personally I used engine hoist to pull my old fence post but if you can get the truck in there you may as well try if you don't have a high lift or engine hoist. Just but smart use a strap or if you have chain put heavy blanket on it so it it snaps it doesn't go flying. Don't use a hitch ball. Feed a strap into the receiver and slide the hitch pin in there to hold it, much safer. Personally I wouldn't use the tow hooks only because that means your trying to pull it in reverse and I have herd stories of that not being good on your truck something to with being bad on your reverse gear, I'm not sure how much of them are true. Just my .02
 

Ratket

Senior Member
Joined
Jul 14, 2014
Posts
3,571
Reaction score
1,300
Location
Arizona-
Ram Year
2018 1500
Engine
Hemi 5.7
^^^ It's not the gear it's the "Half shafts/Axels"

You're truck will pull it right out- no way a "Fence post" Sheers one of those front tow hooks. Remember just 4 low and slow-

Let us know how she goes
 

GsRAM

Senior Member
Joined
Dec 9, 2016
Posts
2,929
Reaction score
2,743
Ram Year
2017 Dodge Ram 2500
Engine
Hemi, 6.4L
Personally, id not use a front tow hook. I'd use a strap on the rear hitch and pull with that. The receiver is made for pulling.

Those front tow hooks can pull, but your asking a lot of them and i could see them bending or tearing the frame if you put enough stress on them. Just my .02 good luck
 
OP
OP
A

adrianp89

Senior Member
Joined
Sep 3, 2015
Posts
3,175
Reaction score
1,273
Location
Tampa Bay, FL
Ram Year
2019
Engine
Hemi 5.7
Thanks for the advice guys, I will let you know what I end up doing and how it works! Probably won't be for another week or so.... waiting for my chainsaw to come in... have to cut down a few things first.
 
Top