Go Back   DODGE RAM FORUM - Dodge Truck Forums > Dodge Ram Generations Forum > 1st Gen : 1981 - 1993 > 1st Gen DIY


1st Gen DIY

3/4 ton wheel bearing replace procedures


This is a discussion on 3/4 ton wheel bearing replace procedures within the 1st Gen DIY forums, part of the 1st Gen : 1981 - 1993 category!
Hi everyone I need help looking for a good video showing how to do a wheel bearing replacement on my ...


Reply
 
LinkBack Thread Tools Display Modes
Old 09-09-2016, 06:40 PM   #1 (permalink)
Junior Member
 
Join Date: Sep 2016
Age: 30
Posts: 8

Ram Year: 1990
Engine: 360
Default 3/4 ton wheel bearing replace procedures
Hi everyone
I need help looking for a good video showing how to do a wheel bearing replacement on my 1990 Dodge w250 power ram three quarter ton.

It feels impossible to find one specifically for my Dana 60 and Dana 44. Any help would be appreciated thank you.

Sincerely
Allenrench


Sponsored Ad
Register to remove this ad.
Allenrench is offline   Reply With Quote
Old 09-10-2016, 06:40 PM   #2 (permalink)
 
crazzywolfie's Avatar
Senior Member
 
Join Date: Apr 2013
Location: under the truck
Posts: 13,502

Ram Year: 81 93
Engine: 5.2
Default
i don't think there is anything major to the job. you just need the special socket to remove the hub nut on the front end. i am pretty sure everything on the rear axle comes apart with basic tools.


__________________

81 dodge d150 custom long box 318 670CFM Holley Street Avenger Carb
89 RamCharger 4x4 318/727/3.21 on 33's
93 ramcharger 318 FI 2wd
crazzywolfie is offline   Reply With Quote
Old 09-21-2016, 04:08 PM   #3 (permalink)
Junior Member
 
Join Date: Sep 2016
Age: 30
Posts: 8

Ram Year: 1990
Engine: 360
Default Pressing the races out
Hi again everyone
Thank you for your help with the other posts. I have a question about pressing the races out of my hubs.
So the inner and outer barrings are the same size and need to get one side out first by hand or is there a tool that can pass through one race and expand to push out the other race?
Any help would be greatly appreciated.

Thank you much.
Allenrench is offline   Reply With Quote
Old 09-21-2016, 07:37 PM   #4 (permalink)
 
crazzywolfie's Avatar
Senior Member
 
Join Date: Apr 2013
Location: under the truck
Posts: 13,502

Ram Year: 81 93
Engine: 5.2
Default
i don't know anyone that has ever had to replace them so i have no idea if they make a tool to do that


__________________

81 dodge d150 custom long box 318 670CFM Holley Street Avenger Carb
89 RamCharger 4x4 318/727/3.21 on 33's
93 ramcharger 318 FI 2wd
crazzywolfie is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
How To Install Repair Replace Front Wheel Bearing Hub Dodge Ram 1500 02-08 1AAuto.com 1ATony 3rd Gen DIY 4 03-24-2016 10:21 PM
Replace Hub / Bearing Unit gbryant General Discussions 7 08-30-2014 09:46 PM
Wheel bearing... 04SPORT Tech Info 0 05-22-2014 01:50 PM
wheel bearing help jlennon79 General Discussions 2 08-25-2013 11:28 PM
1996 bearing seal replace DIY 05singlecabHEMI 2nd Gen DIY 0 09-23-2011 06:33 PM

<




GM Truck Forum
Ford Raptor Forum
Chevy Tahoe Forum
Chevy Cobalt Forum
Chevy Camaro Forum
Toyota FJ Cruiser Forum
Ford Truck Forum
88-98 GM Truck Forum
73-87 Gm Truck Forum
Ford Expedition Forum
Chevy Equinox Forum
Chevy Cruze Forum
Jeep Liberty Forum
Jeep Forum
Dodge Ram SRT10 Forum
Chrysler 200 Forum
Scion xD Forum
Scion xB Forum
Dodge Challenger Forum
SRT Forum
Nissan Titan Forum
Buick Enclave Forum
Cadillac Forum
Cadillac XTS Forum