Can anyone show me there 4" lift on 35's?

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Orion

Senior Member
Joined
Aug 2, 2016
Posts
157
Reaction score
21
Ram Year
2009
Engine
Hemi 5.7L
Sup everyone! Merry Christmas!

I was wondering if anyone can show me a picture of their 4th gen with a 4" lift and 35' tires? I have some christmas money plus I get paid soon so I'll finally have the money to lift my truck up. Was just wanting to see some pictures of some 4" lifts with 35's. I'm planning to put them on a 35x12.50x20 Atturo Trail Blade MT with -44 offset Moto Metal 962's.

I was also considering just going to 6" if its worth the money.​
 
Last edited:

Hemipower392

Senior Member
Joined
May 8, 2013
Posts
928
Reaction score
439
Location
College Station, Texas
Ram Year
2014
Engine
I'm missing 2 cylinders
4.5 Inch lift, on 34.6. Is pretty much the same height as my friends with a 4" and 35's
 

Attachments

  • halo3.jpg
    halo3.jpg
    42.6 KB · Views: 160
  • halo4.jpg
    halo4.jpg
    48.6 KB · Views: 161
  • IMG_2597.jpg
    IMG_2597.jpg
    96 KB · Views: 172
  • IMG_0485.jpg
    IMG_0485.jpg
    97 KB · Views: 167

Ferro

Senior Member
Joined
Sep 17, 2016
Posts
435
Reaction score
198
Ram Year
2016
Engine
Hemi 5.7
4" Zone lift with 35s. I have the Bilsteins set at 1.4. And 3" coil springs in the back.
 

Attachments

  • IMG_1086.jpg
    IMG_1086.jpg
    93.2 KB · Views: 137
  • IMG_1088.jpg
    IMG_1088.jpg
    94.5 KB · Views: 146
  • IMG_1021.jpg
    IMG_1021.jpg
    95.9 KB · Views: 170
OP
OP
Orion

Orion

Senior Member
Joined
Aug 2, 2016
Posts
157
Reaction score
21
Ram Year
2009
Engine
Hemi 5.7L
Those look pretty nice, anyone else?
 

Solid State

Senior Member
Joined
Apr 18, 2016
Posts
824
Reaction score
487
Ram Year
2011 Bighorn
Engine
Hemi 5.7
6" zone w/ 5" rear, bils @ 2.1 on 35x12.5x20 toyo mts...for what its worth, if you dont have any height resttictions, go with the 6" its like $100 more.
 

Attachments

  • 20161210_105555.jpg
    20161210_105555.jpg
    95.6 KB · Views: 171

R.L.K.

Senior Member
Supporting Member
Joined
Dec 1, 2013
Posts
12,803
Reaction score
12,500
Location
Bristol , Tn.
Ram Year
2014 4X4 QC Express 6 speed auto 355 differentials
Engine
5.7 Hemi
The diff in $$ may as well go 6" imo .
I'll be Going 6" with 35"AT s for spring and summer and putting on 37" MT s for deer season and winter driving , this way I'll get maximum time ( 3-4yrs) out of the two sets of tires .
 
OP
OP
Orion

Orion

Senior Member
Joined
Aug 2, 2016
Posts
157
Reaction score
21
Ram Year
2009
Engine
Hemi 5.7L
6" zone w/ 5" rear, bils @ 2.1 on 35x12.5x20 toyo mts...for what its worth, if you dont have any height resttictions, go with the 6" its like $100 more.

The diff in $$ may as well go 6" imo .
I'll be Going 6" with 35"AT s for spring and summer and putting on 37" MT s for deer season and winter driving , this way I'll get maximum time ( 3-4yrs) out of the two sets of tires .

Yeah I have no height restrictions, just maybe my own height LOL.
 

Hemipower392

Senior Member
Joined
May 8, 2013
Posts
928
Reaction score
439
Location
College Station, Texas
Ram Year
2014
Engine
I'm missing 2 cylinders
Just depends on the look you are after. It seems most would prefer the 6 inch, but I ran a 4 inch lift on both of my trucks now. I just prefer the 4 inch look more.
 

fastgti

Senior Member
Military
Joined
Dec 15, 2014
Posts
358
Reaction score
342
Location
Augusta GA
Ram Year
2006
Engine
5.7. hemi
IMG_0776.JPG here is one with my trailer attached IMG_0368.JPG


Sent from my iPhone using Tapatalk
 

mpittman

Senior Member
Joined
Aug 5, 2016
Posts
250
Reaction score
125
Location
Indiana
Ram Year
2015 Big Horn Crew Cab
Engine
Hemi 5.7
6" zone w/ 5" rear, bils @ 2.1 on 35x12.5x20 toyo mts...for what its worth, if you dont have any height resttictions, go with the 6" its like $100 more.

do you know your height of the truck up to the top of the shark fin (if you have one)?

Could you fit into a 7' garage door? 83"?

Love the look of your truck. I'm getting 4" BDS installed, but would rather have the 6".
 

Solid State

Senior Member
Joined
Apr 18, 2016
Posts
824
Reaction score
487
Ram Year
2011 Bighorn
Engine
Hemi 5.7
do you know your height of the truck up to the top of the shark fin (if you have one)?

Could you fit into a 7' garage door? 83"?

Love the look of your truck. I'm getting 4" BDS installed, but would rather have the 6".

So, I have kinda been following along on your posts. You seem to have similar questions that I did when I lifted my truck a few months ago. My main hang up was would it fit in my garage? My truck fits under my 7 ft door. My weather strip is @ 83". My sharkfin is aprox 1" below that. I measured probably 100x. Ultimately i cut a 7" section of 2x4 and set it on top of my truck. Drove in and out of my garage about 5x and it didnt tip over. I already had my bils on, and knew the lift would only ne another 5.5". I LOVE my 6" zone liift, and would have been wishing I got the 6, had I gone 4. That's my 2 cents
 

Solid State

Senior Member
Joined
Apr 18, 2016
Posts
824
Reaction score
487
Ram Year
2011 Bighorn
Engine
Hemi 5.7
That's a nice lift, go with the 6. I have yet to see a member on here that got the 6", and wished they would have only done the 4".
 

fastgti

Senior Member
Military
Joined
Dec 15, 2014
Posts
358
Reaction score
342
Location
Augusta GA
Ram Year
2006
Engine
5.7. hemi
Would the mopar oem air suspension have enough to level out your truck with your trailer?

Sent from my STV100-1 using Tapatalk



From what I am being told on the newer trucks with air ride it would level out. But mine being older I dont have air ride


Sent from my iPhone using Tapatalk
 

fastgti

Senior Member
Military
Joined
Dec 15, 2014
Posts
358
Reaction score
342
Location
Augusta GA
Ram Year
2006
Engine
5.7. hemi
****. I did not see this was 4th gen. Sorry about that. Mines a 3rd gen


Sent from my iPhone using Tapatalk
 

mpittman

Senior Member
Joined
Aug 5, 2016
Posts
250
Reaction score
125
Location
Indiana
Ram Year
2015 Big Horn Crew Cab
Engine
Hemi 5.7
So, I have kinda been following along on your posts. You seem to have similar questions that I did when I lifted my truck a few months ago. My main hang up was would it fit in my garage? My truck fits under my 7 ft door. My weather strip is @ 83". My sharkfin is aprox 1" below that. I measured probably 100x. Ultimately i cut a 7" section of 2x4 and set it on top of my truck. Drove in and out of my garage about 5x and it didnt tip over. I already had my bils on, and knew the lift would only ne another 5.5". I LOVE my 6" zone liift, and would have been wishing I got the 6, had I gone 4. That's my 2 cents

I would love to take the leap of faith and get the 6" lift. I have done the same thing. I put 6" blocks on top of my truck and put one 9" block back near the shark fin, to simulate the extra 3" of the fin. I put all of this in the center of the truck, the highest point. All of the 6" blocks cleared with ease. The 9" block did scrape the flexible weatherstripping around the door frame, but remember, that was in the center of the cab. The top of the cab curves downward towards the sides, so the fin is actually lower on the left side. So, I feel that block would never have hit if it was actually near the fin.

I'm just too nervous to do it. I'd probably get served divorce papers if I couldn't put my brand new truck in the garage :)
 
OP
OP
Orion

Orion

Senior Member
Joined
Aug 2, 2016
Posts
157
Reaction score
21
Ram Year
2009
Engine
Hemi 5.7L
I went ahead and pulled the trigger on the 7" lift lol. Rip Parking Garage
 

mpittman

Senior Member
Joined
Aug 5, 2016
Posts
250
Reaction score
125
Location
Indiana
Ram Year
2015 Big Horn Crew Cab
Engine
Hemi 5.7
So, I have kinda been following along on your posts. You seem to have similar questions that I did when I lifted my truck a few months ago. My main hang up was would it fit in my garage? My truck fits under my 7 ft door. My weather strip is @ 83". My sharkfin is aprox 1" below that. I measured probably 100x. Ultimately i cut a 7" section of 2x4 and set it on top of my truck. Drove in and out of my garage about 5x and it didnt tip over. I already had my bils on, and knew the lift would only ne another 5.5". I LOVE my 6" zone liift, and would have been wishing I got the 6, had I gone 4. That's my 2 cents

What are your Bils set at? 1.4? 2.1? If you level at 2.1 with a 6" lift, wouldn't that give you a total raise of nearly 8" in the front? What did you do in the back? 3" , 5" ??
 
Top