Recent content by loveracing1988
-
Maximum level on Bilstein 5100 without compromising stock ucas
How much tire clearance do you lose from the stock control arms to the zone control arms?- loveracing1988
- Post #10
- Forum: Lifted
-
M/T TIRES!! 2500: General X3, Yokohama, or Toyo?
The General Grabber X3 are by far the best tire I've ever owned. They are not loud, definitely quieter than the mastercraft courser MXT's that I had on my 2500. I am at 13k on them right now, I am at 14.5/32 which puts me at 36,000 miles when I reach 3/32. If I get 30k out of a set of tires...- loveracing1988
- Post #36
- Forum: Heavy Duty
-
Gas tank conversion 2018 1500
Thank you! If I gave you the vin from a truck that has the 32 gallon tank and the vin from a truck that has the 26 gallon tank could you be able to tell me if there are any differences in the fuel lines, evap lines, or anything like that? If so that vin for a 32 gallon is 1C6RR7LTXKS611843 and...- loveracing1988
- Post #3
- Forum: All Mopar Parts
-
Gas tank conversion 2018 1500
So I'm trying to get my buddy we go camping with to swap out his fuel tank for the bigger model. He has a 2018 1500 express crew cab 5'7" bed 4x4 5.7 hemi. He has a buddy at a dealer who told him for 2018 it is unique and can't be switched. Is there anything special preventing the switch on...- loveracing1988
- Thread
- Replies: 3
- Forum: All Mopar Parts
-
6.4 Hemi w/4.10s or Cummins?
Fully loaded my fifth wheel is just over 10k. I really didn't mind towing the same load with my 6.4 and thought it did good, until I towed it with my cummins...- loveracing1988
- Post #35
- Forum: Heavy Duty
-
6.4 Hemi w/4.10s or Cummins?
Your sons truck will get better slowly for about 3000 miles and average 16-17 provided he keeps it stock.- loveracing1988
- Post #34
- Forum: Heavy Duty
-
6.4 Hemi w/4.10s or Cummins?
Anymore you can't look at the cost you have to actually want the diesel. You will never get your money back until trade in time. I loved driving my 14 with the 6.4 with 3.73 gears and loved it ever more when I changed it to 4.44 gears. However after the trans started going and I traded it for...- loveracing1988
- Post #20
- Forum: Heavy Duty
-
Locking hub
Drivers side is the same no matter what. The passenger side is where the disconnect is for 4wd. Could be a bad U joint on the drivers side.- loveracing1988
- Post #2
- Forum: Heavy Duty
-
2500 Shocks
https://www.thurenfabrication.com/collections/tb-2500-14-22/products/thuren-rear-trackbar-kit-for-2014-up-dodge-ram-2500-power-wagon This will also greatly cut down on the hop to the side the 2500's like to do when going over bumps.- loveracing1988
- Post #9
- Forum: Heavy Duty
-
2500 Shocks
Either bilstein 5100 or fox shocks. Bilstein are cheaper but ride a little rougher.- loveracing1988
- Post #5
- Forum: Heavy Duty
-
Looking at the 6.4. Need info.
Apparently I'm in the minority but after having both the 6.4 and a HO cummins I'll never own another gas motor again. There is no comparison when towing between the two, it is so much easier and less stress with a diesel it is borderline boring to tow with this truck. Mileage isn't that much...- loveracing1988
- Post #13
- Forum: Towing & Hauling
-
Cargo camera
While you are at it, I need to add 2 of these to my frame, 55398873AC. Can you give me the part numbers to the bolts and buts that hold them on? I can't find any fasteners in the exploded views just the bracket and the frame,- loveracing1988
- Post #2
- Forum: All Mopar Parts
-
Cargo camera
I am looking for a breakdown of the part numbers of a 3rd brake light assembly for part number 68412027AB. I have a different housing and a different camera and tried to swap the analog camera into my housing and it doesn't fit. Can I buy just that housing assuming I have the correct camera? I...- loveracing1988
- Thread
- Replies: 3
- Forum: All Mopar Parts
-
S&B Intake 6.4 Hemi
You can accomplish the same thing by replacing the filter with a reusable one. You won't gain anything with an intake other than more engine noise.- loveracing1988
- Post #5
- Forum: Heavy Duty
-
5th Gen 2019+ Foglight Add-on harness
The routing for the harness between both lights, has anyone done it in a cummins? I see no where to install the clips. Can I assume this is in front of the intercooler?- loveracing1988
- Post #51
- Forum: M² Mods
