Search results

  1. V

    Headlight switch swap

    That. Would be extremely helpful. And tank you for the pin outs. Much appreciated.
  2. V

    Headlight switch swap

    My truck is a 2000 ram 2500. I did a complete swap of the 98.5 24v into this truck. Wiring and all. My headlight switch is shot its the old pull style i want to convert to the new style turn know. I have the new switch and the connectors with pigtails. Is it as simple as matching the same color...
  3. V

    98.5 24v will start and run really rough for a minute

    I cant tell if the vp is bad or the lift pump i havent been able to test it. The truck has no codes unless you try and press the pedal it will rev to about 1000 rpms and sputter and wont go any higher. I bough the truck for 1400 bucks i haven't checked the fuel filter yet. What is your guys best...
  4. V

    24v swap

    Thats my concern about inspecting the vehicle. I live in NH, with obdII it obviously wodnt pass for a diesel. So I couldnt get away with it. How about a 12v swap since there is no electronics does I just pass anyways. Thanks for the help if there another thread on other fourms like this I.can...
  5. V

    24v swap

    I have a 2000 ram 2500 with the 5.9 magnum amd I want to swap a 24v into it. I can get a donor truck for a good price with alot of work done to it. But it was deemed totaled but everything is fine mechanically. Can I get away with this making the truck registerable I know the vins wont match and...
  6. V

    No Power after build

    Leak down is fine. Other side ranges from 150 to 172psi I checked it again a tonight and it seem better now all around 140 now on the drivers side I probly didn't have the tester in right it's just one of the ones you hold there while someone turns the key. Hooks the plugs back up and now it run...
  7. V

    No Power after build

    I am getting frustrated with this truck i did a cam swap and changed the springs and did a valve job after I took the heads off on the truck they look alright the head seemed flat and i made sure it was alright. But now I'm getting low compression on the drivers side. I made the mistake and...
  8. V

    Fuel sync

    Yeah i drove it around today for awhile and it threw the p1391. So where should i go, and the dbr3 tool to do this how readily available is it at dealerships or shops.
  9. V

    Fuel sync

    OK thanks. I just wasn't sure. And yeas its running very good. It didn't at first i just adjusted the timing on it that's all now it runs quite well. all i need to do is get the pcm re-flashed and i will be set. Thanks
  10. V

    Fuel sync

    I put a comp cams energy cam in my truck with the 5.9 magnum. I keep reading somewhere that i need to do a fuel sync. It seem to run fine. I went to a few local shops and they have never heard of such a thing. Is it only a dodge dealer that knows anything. I haven't gone there yet.
  11. V

    Distributor gear

    I just did a cam swap into my 360 magnum and i have it mostly back together. One thing i forgot to do was line up the distributor gear/oil pump shaft with the number one cylinder. its close after installing the everything can i just adjust the time to make up for the difference or do i need to...
  12. V

    5.9 Build

    Oh and I am also putting in mr gasket .028 thick gaskets
  13. V

    5.9 Build

    Valve Springs for my cam need help So this week I have finally got he chance to tear into my truck. My budget is about 800 bucks max i would like to stay under that. What would be the best part to buy. I have a few ideas to start with COMP Cams Xtreme Energy Camshafts 20-745-9 Harland Sharp...
  14. V

    Random drop in power

    already had the fix done to it about 40000 miles ago
  15. V

    Random drop in power

    99 ram 1500 with the 5.2l sometimes I will be driving along in 5th and just crusin going up and down small hills and sometimes i cant make it up the kills in 2nd or 3rd gear. I will stop and pull over and the truck sounds like a cammed drag car with i high lope but its idling at about 400 rpm...
  16. V

    Inner door skins?

    I have looked at it closer and I guess I really don't need to do the inner skins I can just cut out the very bottom of the panel and tack in a new piece of sheet metal for a lot cheaper then what i have found the inner skins for. I can get the outer skins really cheap and replace them. Then its...
  17. V

    Inner door skins?

    Really I cant even find them on ebay. If i have to fab them myself I guess I can but would rather not. I will keep looking and post something if I find them cheep somewhere
  18. V

    Inner door skins?

    I recently bought a 2000 ram 2500 for 350 bucks that runs i might add. not much is wronf with it but the doors are bad both inner and outer of the doors are rotted i can find the outer skins but do i need to fab my own inner skins or can i get those somewhere. Thanks
  19. V

    starts and runs till its warm

    Never thought of that worth a look. I mean its not like it just went on drive for an hour warm i.mean sittng for maybe 5 mins in 20 degree weather. Would it cause the plate to flex that much. It did sit for 5 years could that have causwd the plate to warp?
  20. V

    check engine light

    All I know is that it has something to do with the tcc or O/D
  21. V

    starts and runs till its warm

    P0505 the iac valve and p0320 crankshaft sensor. It only shows the crank sensor code sometimes. I know the truck wont start when that code is thrown. But I can also tell that the fuel rails dont have a lot of pressure. Not sure what normal pressure would be. But looking into it. It doent make...
  22. V

    starts and runs till its warm

    I have a 5.9l gas motor in a 2000 ram 2500 it started hard when we first got it now it will start somewhat easy and then idles fine. But after it gets warm it will idle up ad down and eventually die and then won't start. New plugs wires are fine it has no brakes working on it. When I turn the...
  23. V

    rim sizing

    I have a 99 ram 1500 4x4 and I wwnt to get new rims for it. Im not spending 1000 of buckson them I just want the 16x8 5 lug.I have google around that the bolt pattern is 5x5.5 but I cant find a single set of rims that have that pattern. Do I have to get wheel spacers with a different pattern to...
  24. V

    Runs rough at half throttle

    Just head the exhaust done on my 99 dodge ram with the 5.2. Had to do it because the cat went bad and screwed up the whole system. It never threw a code so we just replaced it with a high flow magnaflow CAT and 18 inch muffler. Sounds great at idle , but when you go to accelerate at around 1/3...
  25. V

    2000 ram 2500 5.9 will run and just die at random

    It hasn't been used in 5-6 years so that long

Latest posts

Staff online

Members online

Total: 620 (members: 28, guests: 592)
Robots: 1,433

Forum statistics

Threads
195,486
Posts
2,870,933
Members
156,207
Latest member
txram956

Share this page

Top