Search results
-
AlfaOBD
Yea, current version is 17-43-01, hopefully there is a work around to get this to work properly. I guess it is time to start researching a way to possibly revert back to the 17-11-07 firmware. Otherwise I will soon have a OEM Cargo Cam forsale.- dkkinner
- Post #8,548
- Forum: 4th Gen DIY
-
AlfaOBD
Ok, I have been reading through this for a couple days trying to remedy the issue I am having. I could not find any where that someone is having the same issue but i thought i would ask incase there was, or someone has solution. I apologize in advance if this has been addressed and fixed but 855...- dkkinner
- Post #8,546
- Forum: 4th Gen DIY
-
Factory brake controller?
I actually am not sure what the perks would be. I never had mine flashed so I am not sure what you are even able to do with it on the evic- dkkinner
- Post #7
- Forum: Audio & Electronics
-
Factory brake controller?
I am not sure how that works either. But mine was also listed on the window sticker as tow package, but did not have the controller- dkkinner
- Post #5
- Forum: Audio & Electronics
-
Excuse the stupid question
All you have to do is push that little black button on your dash and it will show the Trip A. Hold it to reset it- dkkinner
- Post #8
- Forum: General Discussions
-
Factory brake controller?
I installed a factory one on my 2012 Bighorn. Plug and play did not need to do anything else. Just make sure that the connectors are there for it first. You can have it flashed at the dealer if you want for it to show up on the EVIC but it is not necessary.- dkkinner
- Post #3
- Forum: Audio & Electronics
-
Aftermarket radio issue!!!
Yes that is the adapter that I am using. The wires from the module attached to the truck are going to pin 13 and 2 don't remember the exact colors. Disconnect and same issue. I'm just at a loss, not sure why it should be supplying power to it, with only inserting the key Sent from my SM-G935V...- dkkinner
- Post #9
- Forum: Audio & Electronics
-
Aftermarket radio issue!!!
Key 1 and key 2 wire both go to the 3.5mm jack that was supplied with the aswc-1 steering wheel control module Sent from my SM-G935V using Tapatalk- dkkinner
- Post #7
- Forum: Audio & Electronics
-
Aftermarket radio issue!!!
The harness is scosche with vehicle interface. The key wire is only hooked a 3.5 mm jack for the steering wheel controls. It doesn't matter if it is the boss or a different one. I have now tried 2 radios 1 boss and a kenwood, and it is the same thing. Guess it's time to pull it back out and...- dkkinner
- Post #5
- Forum: Audio & Electronics
-
W150 Spring hanger replacement
Yes I do agree with that Sent from my SM-G935V using Tapatalk- dkkinner
- Post #9
- Forum: Suspension
-
W150 Spring hanger replacement
Yes that is the same one I ordered from them. Front of rear spring mount. Sent from my SM-G935V using Tapatalk- dkkinner
- Post #7
- Forum: Suspension
-
W150 Spring hanger replacement
Not sure if you got one, or made one by now but I just ordered one for my 89 d100 from Auto and truck Springs.com only place I could find it.- dkkinner
- Post #4
- Forum: Suspension
-
Aftermarket radio issue!!!
Ok, I have searched for awhile on here and couldn't find an answer. So I hope this is not posted already somewhere. I bought an after market DD (boss). I wired everything up and it all seems to work good. The issue I have is, as soon as I put the key in the ignition the radio turns on and stays...- dkkinner
- Thread
- Replies: 10
- Forum: Audio & Electronics
-
-
-
New Guy Ralph
Welcome... definitely alot to get from this site!!!- dkkinner
- Post #4
- Forum: Introduction
-
Ohio Roll Call???
Ok so who all is from Ohio. NW ohio for me. -
-
New member
Welcome!!! I havent been here long but lots of good stuff.- dkkinner
- Post #10
- Forum: Introduction
-
Just installed airlift
Thanks, sort of what i am leaning towards. However when i installed them the 1st thing i did was toss the plastic tee and the supplied clamps for the hoses. Went with a brass tee and two eared clamps.- dkkinner
- Post #15
- Forum: Towing & Hauling
-
Just installed airlift
Did you guys all T the airlines or run individual lines. I currently have a T on mine but have been debating ever since i installed them- dkkinner
- Post #13
- Forum: Towing & Hauling
-
Brake Controller
Yea, i might have only got that good of a price because of the history i have with them. Bought my truck, a jeep and dart from them all in the last 1 1/2 years. Sometimes if you talk to your salesman that sold you the vehicle you will also get a little better rate instead of talking directly to...- dkkinner
- Post #6
- Forum: Towing & Hauling
-
New to Dodge but lovin it :) need some opinions on what to do with her
Welcome!!!- dkkinner
- Post #8
- Forum: Introduction
-
Brake Controller
Yea, I will most likely still be getting mine flashed in the future since the truck will be going in for some maint anyways, and after calling around to my local dealers I found one that will only charge me $42 to do it where as the other ones i called wanted well over $100.00- dkkinner
- Post #4
- Forum: Towing & Hauling
-
Brake Controller
On the 11s it will work without the flash just wont show up on the evic. Just installed one on my 12 and it works without the flash. The newer ones require the flash due to setting the gain on the evic where ours is on the controller itself.- dkkinner
- Post #2
- Forum: Towing & Hauling
