Search results

  1. B

    03 hemi Throwing emissions leak code- slight leak

    thanks kx250f, guess that will be the next purchase. Believe it has the NVLD as opposed to the LDP? Saw it online for around $50. Hope thats it! already fixed some hoses, added clamps, new gas cap, think it needed it anyway...i will post results for future help on the P0440 repair!
  2. B

    2005 Hemi won't start

    MPK, did you figure out the isssue? That happened to mine once, my issue I was using a ignition key that was not programmed for my truck....a theft protection device...good luck.
  3. B

    03 hemi Throwing emissions leak code- slight leak

    thanks RedTruck, done alot of research and have checked lots of posts. lots of great info in here. still unsure if any of these pumps or nvld pump can be serviced or easier to just replace. Also where do you buy these special hoses? I have a two into one rubber connector that i cant find...
  4. B

    03 hemi Throwing emissions leak code- slight leak

    Happy 2014 ALL, i have a question regarding the possible solution on the page provided by BOH, it says check or replace purge valve/sensors, how do you check them? can you take them apart and clean them? also something about the canister being plugged and not working properly, can you...
  5. B

    03 Dodge Ram Hemi Engine Can Hardly Idle

    de ja vu. i just went through this hole process a month ago...glad to see you found the problem. when i put my rocker assembly back together it did not matter what cylinder was at TDC. you just have to make sure all push rods are seated at both ends and start tightening the rail from the...
  6. B

    CODE P0300 and rev limiter

    no, never removed the neutral rev limiter...
  7. B

    CODE P0300 and rev limiter

    it seemed to act fine, i cleared the code and all is good now. i was just curious to see if the rev limiter would be the reason for the P0300 code since the rev limiter probably does cause a misfire when it limits the rpm's. Thanks again. By the way, i fixed the exhaust leaks and she...
  8. B

    CODE P0300 and rev limiter

    Would hitting the rev limiter get you a P0300 code? Reason is right after I reved the truck in neutral and hit the rev limiter I received a check engine light and the code was the P0300? Whatcha you think?:drunk:
  9. B

    cam change-engine wont run

    The RAM is finally running and back on the road again. Did the comp cam 260HR swap and have been trying to put a few miles on her. Thanks to all of you for your help...! I also got the SC3815 and keep getting the code P0172. Rich 1/1. Have been doing research on here to remedy the issue. i...
  10. B

    cam change-engine wont run

    Thanks again everyone, i know this info is priceless! I have been following the Cammin Ram page and it is great. Also the dodge dealer/service here is worthless, cant look anything up with out the VIN, too lazy to do it the old fashioned way! Also stay away from Valley Head Service in Canoga...
  11. B

    cam change-engine wont run

    OK. colored chain link only lines up on initial set up like you said form easy ID. THANKS!
  12. B

    cam change-engine wont run

    Is it normal though for the cam chain link to move position's after each engine rotation? I would assume that the timing mark on the cam gear would align with the chain colored link on every other revolution? No?
  13. B

    cam change-engine wont run

    Thanks again Ken! Got another tech question for you all. As far as the timing and timing marks go that are marked on the cam gear, the manual says the mark on the cam gear when pointed at 12 oclock, should align with the single dark colored link on the timing chain. I had to roll over the...
  14. B

    cam change-engine wont run

    what year did the 6.1 come out in? i called the local dealer and he couldnt figure it out?
  15. B

    cam change-engine wont run

    10-4, got it! Where is the best place to order new pushrods? Whats the difference between the 5.7 and the 6.1 rods? are they just beefier? longer too?
  16. B

    cam change-engine wont run

    Thanks Ken. So what am I looking for when I pull the push rods? I plan on swapping the cam to the comp 260. thanks for your input, Todd.
  17. B

    cam change-engine wont run

    finally got a chance to take pics of valve springs-so what do you think? stock?
  18. B

    cam change-engine wont run

    thanks Danny, and thanks again to everyone on here! i will keep posted as progress continues.
  19. B

    cam change-engine wont run

    Ok, just want to make sure i am correct before buying- I need a SC3815. On top of that, I need either the Cam tuner or the PSC1-03. Then a A/F gauge, is this also the wideband? Thanks Greg, Do you have any part #'s for the window switch and relay? You guys Rock!
  20. B

    cam change-engine wont run

    "Simple stuff but helps a lot with a quality idle". Simple Stuff??? LOL Damn, you must be some kind of Genious. That is really some great information...Iv'e gone back over and over all the tremendous amounts of knowledge and information given on here. like mentioned before by...
  21. B

    180 T-Stat?? Where ??

    What do the hemi's run best at? Mine came with a 208 degree stat, I replaced it with a 203 degree. Should I have gone with a 180 degree?
  22. B

    cam change-engine wont run

    Thank You, Thank you, Thank You...Pricless information. Cant thank you guys enough! I will see if I can pick up the equipment you mentioned and try your suggestions. So if it still wont work I will be able to use the tuners on a new set up as well right? One more question, if i decide to go...
  23. B

    cam change-engine wont run

    right On! once i start the tear down and remove valve covers I definetly will..thanks again and my offer still stands for anyone in my neck of the woods!
  24. B

    cam change-engine wont run

    10-4. Thanks again for all the help from everyone. So I am going to swap cams. I know you guys have mentioned to use the vendors here, so who do I contact for the comp 260? Is there a specific model #?
  25. B

    cam change-engine wont run

    Just discovered another issue. Engine wont rev passed 4000rpm. I reach 4000 rpm around half throttle or so and after that if i depress throttle all the way to the floor, no change in rpm...could this all be related to the cam or do i possibly have another problem at hand? never tried to rev...

Latest posts

Members online

... and 9 more.
Total: 1,372 (members: 59, guests: 1,313)
Robots: 1,963

Forum statistics

Threads
195,613
Posts
2,872,565
Members
156,437
Latest member
Ryanbuddy1

Share this page

Top