I have a set of factory 4th gen Laramie LED tails I’m looking to sell. One has a chip on the corner and they have some scratches, but overall they’re a decent set. I’m asking $175 for the pair shipped to the lower 48.
I’m looking to sell a new and complete Morimoto Retro-Quik kit for 4th gen projectors.
Kit includes:
FX-R Projectors
Brackets and hardware
5500k XB Bulbs
35w XB Ballasts
RetroRubber sealant.
$250 shipped to the lower 48.
I know this is an old thread, but I just found it so I wanted to reply. I went through 3 or 4 drivers on my passenger side back in 2017. I also got the “we’ve never seen this. Must be your truck!” Nonsense. They assured me my truck was sending a PWM signal to the drivers so I put an oscilloscope...
I did not. There is no connection for it on the factory hub, which is why the full kit includes a new one. Range is going to be exactly the same as it is now for your keyless entry(less than it would be with the external antenna );same key, same antenna. I’d be interested to see if that board...
Yup, I already have one coming tomorrow. I won’t be using this stuff fob much longer, but I picked it up anyway since it was only $7 and it’ll probably be a few weeks before I get the pushbutton setup installed.
I’m not sure about the 14-16. I have a 13. I installed an aftermarket remote start years ago because I wanted to start it from my phone so it’s not something I looked into previously. I’m getting ready to install Keyless Go and since my aftermarket unit died a few moths back, I figured I might...
I’m not sure if it was mentioned already, but I figured I’d comment in case someone finds this in the future. Even though the 13 models use an external antenna and the Mopar kit comes with a new RF hub, the factory hub is capable of remote start and you can enable it the same way as on the newer...
I know this is an old thread, but I’m bumping it anyway. I’m not sure why, but the 4x10 from Doug that I installed in 2015 stopped working at some point. I didn’t use it this winter because I was working from home, and just realized it no longer works. I gave the Smart Start module and can still...
Unfortunately it’s one of those things that takes some specialized knowledge. You’ll need to have something that can hang off the CAN bus and receive the messages. It will then need to decide the button messages and switch in the correct resistance value to the column shifter button wires. You...
I’m not on the forums all that much any more, but I’m pretty active on the Facebook groups. I’ve really never seen anyone else talk about this. If a lot of people express interest, I’d consider making a module to do it. It’s very similar hardware-wise to one I did for another project.
The clockspring has nothing to do with it. They’re all the same with the exception of the ones with extra wiring for a heated steering wheel. All the clockspring does is get the status of all the steering wheel buttons and send them out on the CAN bus. The message doesn’t even identify what the...
You need a module with dual can buses that can modify certain messages and pass the rest through as-is.
If I was going to do it I would modify one of my existing CAN interface boards to just add another CAN channel. I’m not sure I like the new tails enough to shell out for them, but if I find...
It’s hard to say. Your map files may be compatible with 22.6. I lost my maps, but I was updating from an ancient version. If it were me, I’d probably do 21.9 first so you know you have maps and they’ll also be as up-to-date as possible. I’m trying to decide if I should try to roll back and then...
Where’d you find the 22.5 image? I’d be willing to give it a go and jump back to that and see if it still has RAM themes (I suspect it will). If not, I can then try to jump up to 22.6 again.
Well, I’m shocked, but I drove my truck yesterday after it sitting for a week and my ATC is back. I don’t know why sleeping it overnight wasn’t enough, but I’m not going to complain. Other than the nav, I took a radio from a 17 300 running v14.9.0 and brought it up to 22.6.0 RAM firmware...
Even after sleeping overnight, the radio still isn’t properly displaying the ATC. I may pop my old RA4 in to see if it’s the radio or if I still have something messed up with the HVAC. It’s definitely not an issue with the update not being compatible with my radio because in that case it...
It looks like after sleeping the radio learned all the settings again. One issue I had was that I lost my ATC, but I realized I broke the HVAV config setting when I switched the brand back to RAM. I set it back now and the ATC hard button now turns the system on and the screen shows it’s in...
Some interesting findings with my 17 300 UAQ. I checked with the donor VIN a few weeks ago and there were no updates on the UConnect site, but even I was on my computer earlier I saw the files and remembered I downloaded two earlier this year, versions 16.8 and 16.11 (both came up at the same...
Yeah, it’ll definitely pick it up. The problem is that the software was from before RAMs with UAQs existed, so it has no RAM files and loads a default UConnect theme. I actually changed my brand in my BCM to Dodge so I get a Dodge splash screen and multiple themes. It’s better, but not right...
I just got a notification for this thread and it reminded me of something. As some may remember, I was the first (or maybe second) to put a UAQ in a RAM by modifying the mounts on one from a 2017 300. I’ve been using that radio since, and it still works great. But, it has no RAM theme or splash...
The only setting I’m aware of that seems related to that is the list of modules that are present on the bus. I forget the exact acronym they use for the remote display, but it’s on the list. I spoke with the AlfaOBD devs and that was also the only one they knew of.
I’ve been trying to get an...
Has anyone noticed issues of the GPS accuracy getting worse after the update? I’ve seen reports on the Facebook groups about it.
I’ll get nerdy here for a second for people who don’t understand why this issue is happening with the GPS. The GPS data that’s transmitted from the satellites...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.