Search results

  1. K

    Need a CB guru

    My main question is the 5.7 motor notorious for generating RFI? And if so what's the best way to deal with it?
  2. K

    Need a CB guru

    Excess coax is coiled up under my seat
  3. K

    Need a CB guru

    So I got my new CB hooked up, a galaxy DX929 but I'm having an issue with interference/static. I can't turn the rf gain up much before the blaring static comes in and I'm getting a whine that matches engine rpms. Rpm whine is coming from coaxial and not the power side because it goes away when...
  4. K

    2010 rear end clunk/pop

    Just put new control arms on about a month ago
  5. K

    2010 rear end clunk/pop

    I just had a rear end swapped under my truck after the previous one began to fail. Replaced it with a junkyard pull that only had 60 something thousand miles on it. Shortly after getting the truck back I noticed a pop/clunk when coming to stop and taking off, taking turns, and sometimes slowly...
  6. K

    2500 6.4 buying advice

    Thanks for the replies guys, usually negative things pop up when you do a google search on the 6.4 but then again people with problems are more likely get on the internet and ***** vs the the majority who are satisfied with their truck. I'll be keeping my eyes peeled for a good deal on one...
  7. K

    2500 6.4 buying advice

    So I am going to be looking at buying a new truck within the next year and for I have concluded that a 3/4 ton gasser would fill my needs perfectly. I would like a late model used Ram with the 6.4. Main concern is reliability of the engine/transmission. I have read about the 14s having bad wrist...
  8. K

    4th gen limited slip

    That is a huge relief thank you
  9. K

    4th gen limited slip

    Ok so I just had a new to me rear end put under my 2010 TRX4 the old rear end was open and the new one is lsd. My question is do those C-clips that are notorious for breaking and causing a rear end to explode still affect 4th gens?
  10. K

    Rear Axle Help

    The rearend is going out in my 2010 TRX4 and I'm trying to find the best option to fix it. Can't find a local shop that will rebuild it so my only options are either a pulled part from a junkyard or a remanufactured one. The shop I've talked to that will replace it will either use jasper or a...
  11. K

    2010 Humming

    Bump
  12. K

    2010 Humming

    Is there any possibility the pinion nut is trying to back off again? It happened once before when the truck was my dad's and was covered under the recall funny thing is it's an open 3.92 rearend, I thought the trx came standard with limited slip but that's beside the point, what really bothers...
  13. K

    2010 Humming

    Just on a hunch I pulled the rear diff cover off and the oil was real glittery with what do ya know two big chunks of metal laying in the bottom, they appear to be some type of w shaped clip. I can see something that resembled the fragments in the spider gear carrier but can't see where they...
  14. K

    2010 Humming

    I didn't pay much attention since it started about a mile from work. I'm going to investigate further this evening when I leave. Just by asking coworkers one said hub bearing, one said u joints, and another said failing ring gear
  15. K

    2010 Humming

    Hey all I noticed a vibration on my way to work this morning but couldn't exactly get a feel for what it was. It almost sounds like a hub bearing but its fluctuating. The last bearing I had that went made just a steady noise roar but this is fluctuating like hmmmm hmmmm hmmmm. That's the best...
  16. K

    Wanting new wheels but I don't know what to get

    So from what I understand I should be able to run some 18x10's with -24mm offset paired with 35x12.50r18 tires with only a level?
  17. K

    Wanting new wheels but I don't know what to get

    They're 285/70r17 firestone destination my, they look good but they're not quite tall enough and nowhere near wide enough, can I stuff 35's under there with it only being leveled?
  18. K

    Wanting new wheels but I don't know what to get

    What would be a good tire/rim size combo to run on a trx4 with bilsteins set at 2.8 in the front? I want some new rims and something that fills out better than my baby 285s. Any input is greatly appreciated
  19. K

    Urgent 5100 Help

    He was, he told me never to buy just a strut but to but a fully assembled coilover
  20. K

    Urgent 5100 Help

    Thank you sir! I understand where the washer needs to go, I'm calling my front end guy tomorrow to see if he's available this week. If you ever find yourself down here in tuscaloosa don't ever go to tuscaloosa tire, they'll say your bilsteins are junk and try to charge $1000 for something you...
  21. K

    Urgent 5100 Help

    I don't trust the people who originally did the install seeing as for some reason theyou had to cut a small hole in the fender liner to access the top of the coilover. I have since found a guy that's real good with front end work so it's going to him this week hopefully
  22. K

    Urgent 5100 Help

    Yea he kinda lost me when he said my brand new struts that I was so proud of were junk
  23. K

    Urgent 5100 Help

    I think he was trying to rob me blind. When he said the balance was done I told him to take it off the jack I'm leaving. Just gotta find someone who will pull them apart for me without wanting to rape my wallet
  24. K

    Urgent 5100 Help

    Ok so I think the washer wasn't placed in the right spot when I had my 5100s installed because I'm getting a rattling sound going over bumps. Took it to a local tire shop to have a balance done and wanted them to pull the coilivers apart while I was there. Guy told me that bilsteins were junk...
  25. K

    2010 trx4 losing power when stopping

    So the code it's throwing now is a P3400, cylinder deactivation system bank 1. From my research the first place to start is replacing the cylinder deactivation solenoid but I can't find any good instructions for changing one out. Does anybody here have any input and is it difficult?

Latest posts

Members online

... and 24 more.
Total: 1,191 (members: 74, guests: 1,117)
Robots: 1,587

Forum statistics

Threads
195,472
Posts
2,870,672
Members
156,182
Latest member
mill

Share this page

Top