Search results
-
2017 Dodge Ram 1500 2WD
I have developed a popping / clunking sound when turning at low speeds. No sounds straight or at highway speed. This usually happens turning to the left and does not do any thing while standing still just turning wheel. Any ideas what this could be almost sounded like loose rim but checked... -
Name That Connector?
Hood latch sensor. Sent from my SM-N960U using Tapatalk- Jkieffer
- Post #2
- Forum: Audio & Electronics
-
Door modules and switch
Not ones for power folding mirrors. Sorry. Although I do have some power folding chrome mirrors that I acquired from a 2012. They do need some replacement turn signals and wiring fixes. Just have not had time to work on. Sent from my SM-N960U using Tapatalk -
Door modules and switch
68225101AA Left Side 68225100AA Right Side 68110866AB Switch Sent from my SM-N960U using Tapatalk -
Door modules and switch
I honestly dont know. Maybe someone on here does. Sent from my SM-N960U using Tapatalk -
Tow mirror arm repair
I have this one. Sent from my SM-N960U using Tapatalk -
Tow mirror arm repair
What does your tow mirror look like Sent from my SM-N960U using Tapatalk -
Wheel spacers???
Getting ready to put up for sale shortly Sent from my SM-N960U using Tapatalk -
Wheel spacers???
With my 1.5" Boras I would have to grind maybe less than a 1/4 inch if used with non factory rims. Pretty much the taper part of the wheel stud. (Decided not to use them) Sent from my SM-N960U using Tapatalk -
2WD 1500 Rough Country front leveling springs
275/60/20. Falken Wildpeak With 9" +1 offset rims. I originally had stock +18 offset rims with 1 1/2 spacers. When I got the new rims the shop left the spacers on by mistake and with +1 offset and 1 1/2" spacer the tire rubbed in full turn / reverse at back of wheel well. Looked good but had... -
2WD 1500 Rough Country front leveling springs
I have the RC leveling springs on my 2017 2wd. It rides fine and handles fine but would not say it is as smooth as stock. I also have billstiens on all four corners. I can say I feel every little crack in the road but I cannot say for certain if that is the issue since I have the billstiens... -
Can you get an oem remote start button to work with an eBay kit?
If you have aftermarket remote start I believe the would be have a dedicated hub and possibly different frequency so I doubt it. Most Express's have the rf hub already installed so adding remote start is pretty easy and has been done in the 30 to 100 dollar range using what is already there...- Jkieffer
- Post #3
- Forum: Audio & Electronics
-
Can you get an oem remote start button to work with an eBay kit?
Look at the alpha thread under remote start. It has a the Info you need Sent from my SM-N960U using Tapatalk- Jkieffer
- Post #2
- Forum: Audio & Electronics
-
AlfaOBD
You have to have the correct mirror and sensor in the mirror or upgrade like some of us have Sent from my SM-N960U using Tapatalk- Jkieffer
- Post #3,074
- Forum: 4th Gen DIY
-
+1 offset question.
Ok all I have a small delimmia, when i ordered my +1 offset rims I believed I would like them and get rid of the 1 1/2" bora spacers. The installer showed them to me with them on. When I picked up the truck they were off which I don't like as much. I actually like the look with them on so I... -
Rim Opinion
Maybe on a Silverado? Sent from my SM-N960U using Tapatalk -
2017 Ram 1500 road noise/feel question...
Tire pressure was the key to me. 37psi helps and avoids changes due to temp and low pressure light. I do feel more of the cracks and imperfections in the road almost like I at time am riding on edge of tire. Alignment is right on (within spec) or as best it can be given limited adjustments... -
How To: Install a 2018 4C (UAQ/UAS) Radio in 2013 - 2017 RAM
End panel pops off passenger side dash. Sometime the glove box comes out but either way it is a very quick process. Open glove box, push in top corners and remove the retract cord. Sent from my SM-N960U using Tapatalk- Jkieffer
- Post #598
- Forum: 4th Gen DIY
-
How To: Install a 2018 4C (UAQ/UAS) Radio in 2013 - 2017 RAM
Took about 10 minutes. 7 of which were answering the girlfriend why I needed the part. Sent from my SM-N960U using Tapatalk- Jkieffer
- Post #596
- Forum: 4th Gen DIY
-
I know it’s been beat to death (wheel spacers)
No just enough to offset a small portion of the tires. They will cost enough to ship as it is. Sent from my SM-N960U using Tapatalk -
I know it’s been beat to death (wheel spacers)
Before you by the spacers give me a shout. I have the 1 1/2" boras coming off on Friday for the new rims. Sent from my SM-N960U using Tapatalk -
+1 offset question.
It will be interesting to see what mine look like like with the rims, tires and flares. Sent from my SM-N960U using Tapatalk -
+1 offset question.
Not sure how that will look. I guess I'm torn. Sent from my SM-N960U using Tapatalk -
+1 offset question.
Anyone have insight what a +1 offset would look like with a 9" rim and stock size wildpeak at3w's would look like. It's time for tires and I have 1 1 1/2" Bora spacers on that imam looking to replace. I have a 2017 Express leveled 2wd Sent from my SM-N960U using Tapatalk -
Wheel spacers???
1 1/2" bora spacers with 20 × 9 2wd Sent from my SM-N960U using Tapatalk
Members online
- zrock
- Nietzsche
- CRB357
- CanRebel
- 6speed4.7
- CoZo6
- Lsujker
- jmr
- Catalinbusiness
- gilleydog
- Swims43
- MThompke
- southgaram
- Lufty
- Tmusser2
- Chukbacca
- KalboKalbs
- Treburkulosis
- BucketGruntJL
- Murphy Slaw
- huntergreen
- 2003F350
- Rado
- owldude13
- seafarer
- max2bob
- Jim BB
- speedyslvr
- nlambert182
- MikeinOH
- olyelr
- longhornray
- Edward Taylor
- Ludville1
- Alexxn
- mmhm1998
- Dodge trucker
- stevieb92
- jhouston
- Joe mama
- Mike Townsend
- chopperman1