Search results

  1. 90guy

    2013 Ram 1500 lower Ball joints

    Didn't show up on my phone. Is there a matching Ball joint for the upper or just run the Mevotech MS25506?
  2. 90guy

    2013 Ram 1500 lower Ball joints

    Sweet! What's the part number on the lower ball joints?
  3. 90guy

    2013 Ram 1500 lower Ball joints

    Bump
  4. 90guy

    2013 Ram 1500 lower Ball joints

    Hey guys just had a quick question regarding the lower ball joints on these trucks as I am going to start ordering parts to replace all the ball joints and tie rod ends on my truck. Looks like the PO was rough when pulling the front end apart for the lift. Can a guy buy lower ball joints and...
  5. 90guy

    Looking for pics of red or white lifted trucks

    Just bought a white lifted 13.
  6. 90guy

    Removing spray paint from powder coat

    Well after a few hours I got it mostly done. Ended up melting my Hose on the washer by accidentally rubbing it against the muffler. Need to pull the grill and the lights to really finish it up and grab all the little dots on the bumper. Over all not to bad yet.
  7. 90guy

    Removing spray paint from powder coat

    Well took the pressure washer after it. So far its working just really slow. Just like everything else the PO did to this truck its just half way done. How the paint is coming off and how the powder coat looks underneath. It was not prepped at all. Got luck on that one!
  8. 90guy

    Removing spray paint from powder coat

    That's what I was thinking. I picked up some goof off says it's suppose to take of latex based paints. Going to try this in a spot. If nothing happens then we continue down the list.
  9. 90guy

    Removing spray paint from powder coat

    Actual spray paint applied horrible
  10. 90guy

    Removing spray paint from powder coat

    Bought my first 4th gen. Somebody spray painted over top of the black powder coated front bumper.:mfr_omg: So this spray is starting to peel off really bad and look ugly. Just looking for some ideas. I was going to take the pressure washer after it and try to remove it without removing the...
  11. 90guy

    Figuring out how big of lifting have.

    Noticed the stockers.... Means they will be replaced. What is recommended for these 4th gens?
  12. 90guy

    Figuring out how big of lifting have.

  13. 90guy

    Figuring out how big of lifting have.

    Ill get a picture of the front end later today.
  14. 90guy

    Figuring out how big of lifting have.

    Figuring out how big of lift truck has I just traded my 08 hemi off for my first 4th gen 1500. This 13 has a lift in it and I was trying to figure out how big the lift actually is. What is the easiest way of finding this out. It's on 35s if that helps. [/URL][/IMG]
  15. 90guy

    77 Powerwagon as a daily driver.

    Well sister's boyfriend offered me cash for it a while ago. So i sold this truck. bought an 89 k2500 with a built 454 in it. But now I plan on building a 318 like the one hotrod magazine did making 400hp. Then i think it might go in this old truck.
  16. 90guy

    1977 W100 wheel bearings?

    I just went up to my local napa and ordered one set of front wheel bearings and seals for the front end. As when I pulled my hubs out it pulled the outer bearing off. I ended up cutting the old ones off and having one heck of a time putting it together but so far I haven't had a signal problem.
  17. 90guy

    77 Powerwagon as a daily driver.

    Single? lol 3 inch header into a 2.5" true dual.
  18. 90guy

    77 Powerwagon as a daily driver.

    Man just a little bit of a difference. It might see a mud pit a time or two though. I guess it is what I am going to have to deal with.
  19. 90guy

    77 Powerwagon as a daily driver.

    Had a little time before work. PCV is on the way and kick down adjustment needs to happen. But here it is at idle. https://www.youtube.com/watch?v=ojRGWmyHmSo
  20. 90guy

    77 Powerwagon as a daily driver.

    That could also be the fact with this motor. I didnt think the cam sounded to radical with this exhaust. I have to be at the idle of 1000 rpm for it to smooth out though. :/ The carb is a 1406 edelbrock 600cfm. I'll grab a video of it tomorrow.
  21. 90guy

    77 Powerwagon as a daily driver.

    Lol. Needs a lot more cam haha. Runs a lot better now though since I have had time to work on it. I guess its just the 318 thing with a cam. Starts making good power around 3 grand. Gotta adjust the kickdown lever on my days off.
  22. 90guy

    77 Powerwagon as a daily driver.

    Well motor is in. Motor mounts I picked up worked had to mod the right side one a little bit to make it fit. And the motor runs and idles good. Just feels like a dog though :shocked:. So tonight I am installing a MSD street fire Ignition onto it and will go from there.
  23. 90guy

    77 Powerwagon as a daily driver.

    Haha true. This worn out 360 would go over 100mph. It would take a while but it would get there. We will see if these mounts are correct and go from there.
  24. 90guy

    77 Powerwagon as a daily driver.

    Mopar guy up at napa says he has a set just need to go out there one day and grab them. As for a cam it is a pro comp. No idea the grind. Just bought it with 5000 on it. 30 over in the cylinders. That 2wd just buried the speedo that I bought it out of. Defiantly can hear the cam in it. High rise...
  25. 90guy

    77 Powerwagon as a daily driver.

    Well pulled the motor and found out it was a 360 in it. I can grab the crank and turn it over by hand. Have a torque converter for a 318 but now I need to find a set of motor mount brackets for a 4wd with a 318. Anyone know where I can find a set?

Latest posts

Members online

... and 7 more.
Total: 1,273 (members: 57, guests: 1,216)
Robots: 1,369

Forum statistics

Threads
195,406
Posts
2,869,846
Members
156,074
Latest member
Francisco50

Share this page

Top