exhaust

  1. R

    2020 Ram 1500 Classic single exhaust size/options??

    Looking to upgrade my exhaust to get a bit of a deeper sound, but I'm not sure of the inlet/outlet size for the muffler. I have the single exhaust. I assume it's 3inch and 3 inch but not 100% sure. Also, will a flowmaster 40 series muffler give me a deeper sound but not too loud and aggressive...
  2. Just Bob

    Not quite DIY - Kooks Shorties - Go to a shop!

    Installed Kooks 35101110 Torque Series Shorty Headers today. Six hours in Mac's Custom exhaust. I had already modified the Y pipe at Mac's. I have to tell you, this job would be pretty tough without a lift. I tried. The previously installed Lyell's muffler (shown next to stock) cut a lot of...
  3. WillT

    Ecodiesel straight pipe

    Hey, Got a 2015 ecodiesel, got it fully deleted and tuned about a year ago now and has been running great. All that is left on it is the muffler. Thinking about straight piping it to get more sound. Just wondering if that would effect the engine in any way, does it need to have backpressure or...
  4. J

    Diesel exhaust system component theft

    I recently had some one try to steal the catalytic converter in my gas vehicle. Wondering if diesel exhaust system components are prone to the same. I have a 2022 RAM 5500 and it has all the factory exhaust system components. I know there is a Selective Catalytic Reduction piece and other...
  5. LongTom

    2011 Ram 2500 5.7L Poor Performance

    Hello everyone, I recently purchased a 2011 Ram 2500 5.7L 4x4 Crewcab Longbox with I believe 3:73's a few weeks ago. Truck has an engine code (P0420) for catalyst efficiency below threshold on bank 1. Truck feels a little underpowered for 390 HP and If i am absaloutley driving like a grandma at...
  6. LongTom

    2011 Ram 2500 5.7L Poor Performance

    Hello everyone, I recently purchased a 2011 Ram 2500 5.7L 4x4 Crewcab Longbox with I believe 3:73's a few weeks ago. Truck has an engine code (P0420) for catalyst efficiency below threshold on bank 1. Truck feels a little underpowered for 390 HP and If i am absaloutley driving like a grandma at...
  7. I

    2004 Ram 1500 5.7L Hemi Is Producing Oil Smoke At Idle

    I bought a used truck from marketplace a while ago and didn't see this problem when I was test driving it, good job me. I have now figured out that it is burning a heavy amount of oil when it is idling. If I sit for a minute at idle and then rev the smoke gets forced out of the exhaust and...
  8. trainthemane7

    4th Gen Aero Direct-Fit Replacement Muffler

    Magnaflow Direct-Fit Replacement Muffler (09-18, 19-23 Classic 5.7L RAM 1500 w/ Factory Dual Exhaust) like new! I put this on my 20’ Warlock and it was just a bit too loud for me. It was on the truck for just 20 miles before I replaced it with a Flowmaster Super 44. This is a direct fit...
  9. J

    Borla to quieter exhaust swap.

    Hi All. I recently picked up a 1500 5.7 with factory Borla exhaust. Love the truck but it's too loud for me. I'm looking to swap this with a stock exhaust that's in very good condition and quiet. I have 6,300 miles on the truck now. I would be looking for a replacement with under 25k and have a...
  10. LaramieLimited

    Potential Header install on 2012 Ram 1500

    I've found a ton if great information in quite a few pinned threads, thanks to all of those that contribute to the wealth of knowledge here! I have a 2012 1500 Laramie that is sitting at 116k, I've had her since 5k miles, she has been a great truck. I have had to deal with the exhaust bolt...
  11. JCarr98Ram

    H pipe or x pipe help reduce clapper exhaust noise?

    Hello, I just got true dual exhaust, high flow cats, 2.5in inlet/4in outlet. And now I have a clapping noise when I am driving. How can I fix the clapping noise? Is my truck safe to drive or will I ruin my engine/ exhaust?
  12. JCarr98Ram

    Studs for headers

    Hello, Wanted to see if some one can answer a question that I have. Currently, I am replacing my stock manifolds with JBA cat4ward headers. I am looking to buy some ARP studs for my 1998 dodge ram 1500 5.9L 360 engine,but they are giving me studs for a 5.9L cummins. Can I use the studs for the...
  13. SugaryClapz

    Need help removing exhaust

    So I wanted to take off my old exhaust and replace it with carven but my bolts seem welded on compared to the install video carven did. Not sure how to take them off because they’re supposed to be 15mm but that is too big. Any help with getting these bolts off will help! (Pics include front...
  14. JCarr98Ram

    Need Help with Exhaust

    Hello Everyone, Really need help with finding a performance parts to replace my old exhaust that connect to the headers up to the cat. I've already found a cat back exhaust to replace from there. I've tried looking at summit racing, magnaflow, and Jegs. My goal is to find some way to turn my...
  15. A

    Exhaust for 4.7?

    I received a 2004 Dodge Ram 1500 4.7 4x2 with only 118k miles as a gift about a year ago. It sounds nice already but is it worth it? if so then what exhaust should I get?
  16. Socalramfan

    Vararam with Carven Exhaust…. Sound bits?

    Anyone have a Vararam and Carven exhaust set-up? Been curious as to what the sound would be like. I’ve got the Vararam and considering the Carven. Both items sound amazing independently, with great reviews, so I’m curious to the combination of using both. Feed back and any sound bits / video...
  17. M

    Exhaust Manifolds

    Hey Y’all, sounds like I got a leak in my passenger exhaust manifold. I was looking at maybe upgrading both instead of just replacing. Can anyone suggest a good performance enhancing replacement? I was looking at maybe doing all Mopar but wasn’t sure if that was the best way to go about it. Thanks!
  18. J

    Shorties quieter than stock?

    Hi, I need some help and I hope there might be an explanation. I just got some BBK shorties installed (plz dont bash me about BBK I know they arnt the best and getting shorties, I had broken bolts) and they seemed to make my exhaust quieter? I had Flowmaster super 10 muffler and stock manifolds...
  19. Bmags

    For Sale Solo Performance Mach44 Mach 44 Catback Exhaust Gen 4

    I am selling my used Solo Performance cat back exhaust system. It’s in good shape overall, but I’m just looking for something a little louder. Leaning towards the Carven Progressive. It’s a good system with no drone, and a nice amount of volume when you step on it. Quiets up nicely when...
  20. N

    2016 Ram Sport exhaust ideas

    Just bought a used 2016 Ram Sport. Looking for ideas to upgrade the stock exhaust. Thank you in advance.
  21. C

    Exhaust setups

    This is my first post so I apologize if I'm doing something incorrect with this post. For context I drive a 5.7 2022 1500 big horn. Has anyone here done any exhaust work to their hemi? I recently got this truck and am loving it, but am extremely underwhelmed with the exhaust noise. I want to...
  22. 70chall440

    2014 2500 5.7 header recommendations

    As the title says I have a 2014 2500 Big Horn with a 5.7 which has about 48K on it. I want to replace the stock exhaust manifolds with some shorty headers and am looking for recommendations. I am not necessarily after max HP gains insomuch as I want to fix the broken studs and gain a little bit...
  23. LifeinOverdrive

    5th gen Ram Exhaust Options

    Hello Everyone, I have done my homework and came up with a list of the best exhaust systems for the 5th gen ram 1500. Make sure to check them out on my channel here: Best Exhaust kits for your truck Let me know what your favorite sounding one is!!!!
  24. R

    3.7 exhaust question

    Hi all, I tried to attach a Flowmaster 40 series to my 3.7 because I was told the exhaust we run stock on an 07 1500 is a 2.5” when in reality it’s a 2.25” could I just throw a 2.5-2.25 reducer on both ends and call it a day? Would it still pass MD emissions or will I need to keep an OEM muffler...
  25. S

    Long tube headers

    I have a GEN 3 2008 Dodge Ram 1500 with a 5.7 and I am getting ready to fix the broken exhaust bolts. Since I am going to take it all apart I want to do long tube headers. Has anyone had problems with check engine lights or routing issues?
Top