Recent content by abouttobeglue

  1. abouttobeglue

    How to remove nut sert for tailgate assist?

    My deezee assist nutsert stripped out a while back and I chuckedbit, finally got a new one, how can it get the old nutsert out?
  2. abouttobeglue

    Anybody have experience with the Nitto 420V tires?

    A few years ago I wanted the 420s, but they were out of stock, I got the nitto 421qs in a 275/60r20, they were initially good in the wet, after about 10k they wore funny, road like ass, and were heavy as hell to boot. I will never buy an asymmetrical tire again. I had better luck with blacklion...
  3. abouttobeglue

    Hella halogen bulbs?

    Thinking about swapping my bulbs from Sylvania xtra vision to hella high wattage or 2.0s, anyone tried hella bulbs as an upgrade? Not looking to do LEDs, thought about sealights, but it seems can bus is hit or miss. Mines a 2016 with factory quads
  4. abouttobeglue

    Want to lower rear

    My brother did do a front leveling kit on his 2012 z71, it rode lack hammered ass after he did it
  5. abouttobeglue

    Want to lower rear

    I never had an issue with ride quality and using stock shocks lowering the rear on my 12 and 16 both rcsb. Used mcgaughys 44055 on both, both were a little higher in the rear. Now lowering it 2/4 and getting it to ride right, that was an expensive rabbit hole.
  6. abouttobeglue

    Want to lower rear

    https://suspensionsuperstore.com/2009-2018-ram-1500-2wd-4wd-premium-2-rear-lowering-coils-272920#! You can use airlift bags that go in the springs for loads. I have the 60824 kit, but my truck is lowered 2/4. I had the mcgaughys 44055 kit on my truck before I lowered it fully, road fine, no...
  7. abouttobeglue

    Belltech 2/4 drop - Need new front shocks

    I'm currently running doetsch tech nitro slammers front and rear, they're a lot firmer than the belltech nitros. I had good ride with kyb monomax and had some kyb excel gs front and rear that rode nice, but were too soft for the country roads I used to live on. May put those back on at some point
  8. abouttobeglue

    Vararam intake VS KN intake

    I had the kn 63561 for 4 years, switched to the jlt intake. Jlt is better made, much easier install. About the same price
  9. abouttobeglue

    Truck got rear ended can I swap bumpers?

    My 2016 lowered Express got rear ended at a stop light. Initial quote is close to 8k after they add for my sway bar. I have the factory dual exhaust bumper, thinking of seeing if I can swap this to the paintable bumper with no cutouts, and since my exhaust is fubared on the driver side...
  10. abouttobeglue

    What exhaust are you running

    I like the Jones flow pack pretty well, not too much drone, good idle, sounds awesome when you floor it. Favorite is still the Gibson mwa race muffler, this is probably 3rd favorite. Bang for buck it's the best, it was 35 bucks fron summit, already had a y pipe, 70 bucks to get it welded
  11. abouttobeglue

    What exhaust are you running

    I've got a Jones flowpack now with no resonators. I've had pypes violator, pypes m 80, black widow Widowmaker, Gibson mwa race, classic chambered power stick, 14 inch total flow,
  12. abouttobeglue

    Fuel Sensor Fail... should I fix it?

    I just had mine done last week, cost me 900 parts and labor, also had to pay for a rental car for a few days. The whole pump wasn't bad, but the sensor is built into it. Either way makes sense to replace the whole thing to me than have to go back and replace the pump later.
  13. abouttobeglue

    Muffler options

    Pypes violator bolt in kit for no drone or Gibson mwa for very little drone with a better sound
  14. abouttobeglue

    Shock Recommendation

    I switched mine last week from kyb monomax to doetsch tech nitro slammer. Rides better, little stiffer at times.
  15. abouttobeglue

    Do you have to remove tail pipes when replacing muffler?

    Grease the hangers with some pb blaster and use a big pair of channel locks like an exhaust hanger removal tool
See more

Latest posts

Members online

Total: 409 (members: 10, guests: 399)
Robots: 1,314

Forum statistics

Threads
195,597
Posts
2,872,368
Members
156,406
Latest member
1Popeye

Share this page

Top