Recent content by Anthony Bulger

  1. Anthony Bulger

    O2 Sensor wiring pinout

    Can someone verify my understanding of the wiring on the O2 sensor plug. Pin 1 - O2 Heat - 12Volt + Pin 2 - Ground - 12Volt - Pin 3 - O2 Return (Upstream or Downstream) - ? Pin 4 - O2 Signal - ? My questions are on Pin 3 & 4. Generally, 1 of these is a 0-1 volt output from the sensor since...
  2. Anthony Bulger

    Intermittent Electrical Module issue

    No, it's not solved. I quit for several weeks but recently just came back. I thought I might have accidentally fixed it with all the fiddling with different things, but that's not the case. As before, I'll be driving along and all of the sudden everything resets / turns off and back on. But...
  3. Anthony Bulger

    Intermittent Electrical Module issue

    I've used Alpha OBD, AppCar, HPTuners MVIC3, and had no codes, until just recent. I received a Lost BCM Communication code. a U something, I wrote it down at the house.
  4. Anthony Bulger

    Intermittent Electrical Module issue

    Ok so I have a 2019 Laramie Crew Cab 4x4 5.7L non etorc. She generally sits in the driveway during the week as I travel extensively for work. So, I only drive her occasionally on the weekends. Here is what has happened so far....... 3 weeks back, Friday went out to dinner with the little...
  5. Anthony Bulger

    5TH Gen Alfa OBD

    Not sure if the HD is the same as the standard Ram. Also 2020 year is going to be different than the 2019, RAM made a lot of changes from the 2019 DT to the 2020 DT on the BCM and ECM setups from my understandings. Did you make the correct wire modifications under the hood too?
  6. Anthony Bulger

    5TH Gen Alfa OBD

    Need help! I have lost my gear display in the lower center section of my dash gauges. I can scroll thru the steering wheel setup and select display gears "ON" and nothing appears in the | | | | area at the bottom. I used to have it show like P|R|N|D and the gear I was in. I can't seem to...
  7. Anthony Bulger

    5.7 Performance Part Questions

    Well, spent Easter weekend wrenching on the truck. I managed to get the long tubes wrapped & installed, swapped the ECU, added a catch can, and some other miscellaneous things done. I'll do new plugs with the intake swap. I just haven't had time to mess with the intake and get it ready...
  8. Anthony Bulger

    5.7 Performance Part Questions

    Here are some images to show the difference between the Kooks and the RemFlex gaskets.
  9. Anthony Bulger

    5.7 Performance Part Questions

    Luckily I have all those in my tool box. The Remflex gaskets showed up today. Wow, those are different from the others. Nice and thick.
  10. Anthony Bulger

    5.7 Performance Part Questions

    Really? Have a part number or something for it? That might be easier in the long run. lol
  11. Anthony Bulger

    5.7 Performance Part Questions

    I'd be happy to give him a call Monday if you seriously want one, just PM me. I would imagine he has a couple laying around in his yard, after all he runs one of the biggest part recyclers in Dallas.
  12. Anthony Bulger

    5.7 Performance Part Questions

    Oh, I plan to clean it up, once I get a chance to strip it down. Thanks for the porting link, I was thinking about that as I have access to a flow bench. I'm just curious about the difference in grinding the composite compared to the cast. I would assume I might have to get some different...
  13. Anthony Bulger

    5.7 Performance Part Questions

    Look at what I found. And all I had to do was buy a case of beer for someone. He was even nice enough to pull it off the truck for me. I might have to take him to lunch.
  14. Anthony Bulger

    5.7 Performance Part Questions

    Also, I'm guessing I'm a little confused with some of these write ups on the 6.4L swap. Some of them are using a MSD8969 Timmer module to control the variable intake runners. I'm guessing this is either a requirement on the cars or say an older 5.7L that's being converted? Because doesn't my...
  15. Anthony Bulger

    5.7 Performance Part Questions

    Today I did to do some maintenance on the truck. During the winter freeze, I thought I had given enough time for the washer lines to thaw out, and well I guess I hadn't so the pressure blew of the hoses from the nozzles. Anyway, I pulled the hood heat shield off and fixed it. Well last night...
See more

Latest posts

Members online

... and 23 more.
Total: 1,381 (members: 73, guests: 1,308)
Robots: 1,697

Forum statistics

Threads
195,477
Posts
2,870,739
Members
156,195
Latest member
jerllouk

Share this page

Top