Recent content by Ashkon
-
Average time for a built engine to be done?
Ended up driving 13 hours to South Carolina to find that out in June lol- Ashkon
- Post #51
- Forum: Engine & Performance
-
Average time for a built engine to be done?
it was in the tune.- Ashkon
- Post #50
- Forum: Engine & Performance
-
Average time for a built engine to be done?
Idk if anyone was following my build lol But truck is almost done.- Ashkon
- Post #48
- Forum: Engine & Performance
-
PCV System Whipple
Lol still havnt got the truck back get.- Ashkon
- Post #19
- Forum: Engine & Performance
-
Average time for a built engine to be done?
Alright. lME sent me a brand new gear with limiter installed. I installed it today and teuck sounded great, even chopped. Killed it and wouldn’t start back up. Through the P0016 and both bank rich codes. Help throttle down all the way and got it to run and eventually ran on its own. When I go...- Ashkon
- Post #47
- Forum: Engine & Performance
-
Average time for a built engine to be done?
Alright pulled timing cover and found phaser has some slack when turning the motor over. Anybody seen something like this before? This is a brand new phaser from Mopar. Timing seems to be right. I can turn the motor over and sometimes phaser will not move but chain will. Not enough to jump a...- Ashkon
- Post #46
- Forum: Engine & Performance
-
Got my Kooks headers
Mines are bare and still look great even with the procharger being on.- Ashkon
- Post #9
- Forum: Engine & Performance
-
Average time for a built engine to be done?
Anybody seen this? Shows timing off but then shows cam and crank are in sync.- Ashkon
- Post #45
- Forum: Engine & Performance
-
Average time for a built engine to be done?
they said they are 1000 percent sure it is not timing but said he would look at the build sheet and check the readings to wrote down.- Ashkon
- Post #44
- Forum: Engine & Performance
-
Average time for a built engine to be done?
Not sure what else would throw a P0016.- Ashkon
- Post #42
- Forum: Engine & Performance
-
Average time for a built engine to be done?
All of that work and money. Got it put in. Started it keep getting a P0016 code. Hard as hell to start, runs bad and no chop. Looks like they set timing wrong. Not counting after they installed the pick up tube in the wrong spot.- Ashkon
- Post #40
- Forum: Engine & Performance
-
Average time for a built engine to be done?
Just picked her up!- Ashkon
- Post #38
- Forum: Engine & Performance
-
Average time for a built engine to be done?
Well looks like she’s done. Got these yesterday afternoon- Ashkon
- Post #35
- Forum: Engine & Performance
-
PowerStop or StopTech??
Had a buddy with a ctsv and I put the R1 rotors and pads on it. Had the same results with his.- Ashkon
- Post #18
- Forum: Engine & Performance
-
Members online
- Treburkulosis
- PDub72
- PNWagon22
- Renegade17
- Longhorn1500
- Paulnrld
- Black-Wolf
- oober
- FJ Mike
- Curtis MacConnell
- KeithP
- TNcruise901
- Lsujker
- RamDiver
- BucketGruntJL
- dyer0908
- Swims43
- Chukbacca
- Mx10rs
- nunyabiznes
- 06 Dodge
- RBT1
- michaelcarlson2
- MJP81
- Sheapdog
- G-Ride990
- UAQDADDY
- mikeru
- 97RedRam
- caulk04
- brendan185
- shmedley
- TRK_GANG74
- RamCares
- OHHemi
- StateOfMind
- photoguynorth
- VOwens
- Musky Mike
- Kilo
- icecoldak
- netshadoe
- maxmedic73
- Got 1
- s_wall98
- Dodge trucker
- RJR83
- Douggie
- Bmags
- crackerjack1957