Recent content by Bking99

  1. Bking99

    Alternator issue

    battery gauge started reading high a few months ago and over time kept getting higher and higher. Now it’s just below the red. Tested alternator and said bad diode. Replaced it with a new one and the new one is doing the exact same thing. High reading on the gauge. If I push and hold the window...
  2. Bking99

    Differential problems

    Exactly what I was thinking. Appreciate you sticking around and helping man. Thank you
  3. Bking99

    Differential problems

    Well I just got it!! Since he said pressure, I took the handle end of a ball joint separator between the axles and pushed on the forked end against my shoulder using the frame as leverage and it moved so I rolled the spider gears in without the thrush washers first. Then I used the ball joint...
  4. Bking99

    Differential problems

    First gear? He said for Chrysler rear ends they take the carrierout and use a vice. They are the devil.. his words
  5. Bking99

    Differential problems

    Well I made a phone call and he said there needs to be an extreme amount of outward pressure on the side gears to get that pin in. I cant even get he thrush washers on the spider gears to roll in with them. They just peel off as soon as they roll around to the solid part of the carrier. Did you...
  6. Bking99

    Differential problems

    Why does it look like your clutch packs aren’t in the half round groove? Looks like they are slightly down a bit. Might just be the angle
  7. Bking99

    Differential problems

    Mines a 9.25 with 3.92 gears
  8. Bking99

    Differential problems

    Here’s a pic of the situation and a picture of the clutch packs. I know the spider gears aren’t in yet but just showing how the gap isn’t big enough for the carrier pin
  9. Bking99

    Differential problems

    I get what you mean. No, I cannot see the c clip anymore. It’s at the same depth as the clip on the axle I didn’t touch. Something is holding the entire side gear out a little. I think it’s the clutch packs. That side gear has to be resting on the final disk instead of going through it like it’s...
  10. Bking99

    Differential problems

    Are you talking about the c clip that holds the axle onto the side gears? I pushed the axle inward, towards the other axle and removed the c clip from the axle end and then pulled the whole axle out of the shaft. Is there another c clip you are referring to?
  11. Bking99

    Differential problems

    Yes I compared them. They were identical. Even when I tried reinstalling the original one, the carrier pin still doesn’t fit between the axles so even if I wasn’t replacing the axle there’s still a problem somewhere. It’s something I did I’m sure I just can’t figure out what is holding it out...
  12. Bking99

    Differential problems

    Put the c clips back in the axle and pulled them out as far as they would go. Even had someone pulling on it from the wheel side to hopefully get the clearance for the pin but no luck. I feel like maybe one of those clutch pack discs are not turned correctly maybe? Like maybe the last one with...
  13. Bking99

    Differential problems

    Swapped a bad axle shaft and when replacing the new one, the carrier pin that goes up thru the spider gears won’t fit between the axles now. I tried putting the old shaft back in to see if it was something I did or if the new shaft was a bit long and it wouldn’t work either. The spider gears...
  14. Bking99

    Wheel wobble

    2003 5.7 Hemi, quad cab, 2wd.. Rear right wheel wobbles visibly in the mirror. Shakes in the steering wheel, seat, cup holders.. everything. Not too bad at normal speeds but between 70 and 78 or so it’s the worst and calms back down after 78mph. I sideswiped the little gas pump protector poles...
  15. Bking99

    Ball joints

    New member, first post but I've been browsing these forums for a long time. Have a question about how to tell if the shop that replaced my ball joints actually did in fact replace them... are there any identifying features or markings on the stock ball joints that would indicate what I currently...
Top