Recent content by Brian Lee
-
5TH Gen Alfa OBD
I have a 2019 Ram 2500 Big Horn. I tried to set my DRL's to turn signal's but the switchback LED's I have installed caused a failure message from the front turn signals with that configuration. I wanted to switch from DRL's set to low beam because I work on a military base and have turn to off...- Brian Lee
- Post #54
- Forum: 5th Gen DIY
-
5TH Gen HD Proximity Entry DIY Upgrade
Interested in doing this for my 2019 bighorn 2500. could you send me a pm Jimmy07 and let me know what I need Thanks- Brian Lee
- Post #28
- Forum: Heavy Duty
-
-
Tailgate Damper
Benny, Could you get me a quote for a tailgate damper for a 2019 ram 2500 Bighorn? Thanks- Brian Lee
- Thread
- Replies: 2
- Forum: All Mopar Parts
-
2020 Ram 2500 Tailgate Damper Kit
I don't want to step on anybodies toes but.....................When I looked up part numbers for the dampener for my 2019 ram 2500 I got a different number #68362518AA. The part # referenced above will not fit my truck. I also ordered on from EBay that fits 2019 and up trucks. When I got it I...- Brian Lee
- Post #31
- Forum: Heavy Duty
-
UAV 8.4 nav upgrade
I have a 2018 Ram 2500. I have installed the UAQ (w/Nav). I also installed the auto temp sensor and extra required wiring for it and converted it over from 4 speed to 7 speed. When I adjust the temp up and down it goes in one degree increments. If you check out the thread in the 4th gen DIY...- Brian Lee
- Post #11
- Forum: Audio & Electronics
-
UAV 8.4 nav upgrade
I converted mine over from a 5 inch screen to the 8.4 w/nav. I opted to change mine to include the auto temp and everything has been working great.- Brian Lee
- Post #4
- Forum: Audio & Electronics
-
Anybody else get a new camper this season?
I've got a sherline tongue jack and also my haul gauge and app. Both were right around the same. It has a rear kitchen with the fridge in the back and I generally put all the stuff we pack up in the front just to get a little more weight- Brian Lee
- Post #35
- Forum: Towing & Hauling
-
Anybody else get a new camper this season?
2020 Mallard. 36 ft, weighs about 7400 lbs empty and tongue weight is around 750 empty. Loaded up Its around 8300 lbs and tongue weight around 850. Tow it with my 2500 and it pulls great.- Brian Lee
- Post #29
- Forum: Towing & Hauling
-
Akkon projector experience
In 2018 they locked the OBD port for most changes. check with mpgrimm2. He makes an adapter that bypasses it. -
Weighed my truck & trailer. Wdh dialed in enough?
Something doesn't look right. Is the top bolt of the ball mount actually go through the reciever mount? I have a Husky Centerline that I use and have included a couple pictures of the ball angle and where the bars actually make contact with the plates. I believe there are 3 washers on mine that...- Brian Lee
- Post #17
- Forum: Towing & Hauling
-
What did you do with your 4th Gen this week?
Very good quality and customer service was very good too. I had the driver side with a little just a little bit of rust on the end of the bar and they sent me a new one. I like that they are 6 inches wide. My tire and fender flares stick out a bit and the running boards seem to line right up...- Brian Lee
- Post #35,907
- Forum: General Discussions
-
How To: Install a 2018 4C (UAQ/UAS) Radio in 2013 - 2017 RAM
My Tradesman came with the 5 inch screen, so I didn't have the backup camera in the mirror, it was on the display already. I did add the RCA adapter that I got from mpgrimm2 and hooked up a camera in the front and I can switch back and forth between them but not at the same time.- Brian Lee
- Post #2,245
- Forum: 4th Gen DIY
-
Looking for a tonneau cover
https://www.tonneaufactoryoutlet.com/ If you are looking for BAK covers or anything else on their site, make sure to chat or call them and you will get a price considerably lower than what most sites list. I got my BAK revolver fro a lot less -
What did you do with your 4th Gen this week?
Some state parks in Florida are now open so got out and did some much needed relaxation- Brian Lee
- Post #35,848
- Forum: General Discussions
