Recent content by chili81

  1. C

    Diff bearing replacement - shim location (and pinion shaft length?) change in 2014?

    I only have stick or flux too - and very limited skills with either. Sounds like a good trick though to keep in mind for the future.
  2. C

    Diff bearing replacement - shim location (and pinion shaft length?) change in 2014?

    I just got valvoline synthetic 75w-140. I won't be putting another 30k of towing on it - so it should outlast me or the rest of the rust bucket.
  3. C

    Diff bearing replacement - shim location (and pinion shaft length?) change in 2014?

    Yeah i bet that's what most private shops would do - just swap for a used axle. Remanufactured ones are like $3k. I assume dealer would just go new - idk how they operate. Got it back together today except the cover and filling it back up (and putting brakes back on). Seems to have gone...
  4. C

    Diff bearing replacement - shim location (and pinion shaft length?) change in 2014?

    Yeah that setup looks like it would work well. In hindsight, cutting the old ones off is pretty easy if you just jump right to that - if you wanted to skip buying one. But adding one of those to the kit would be nice. This torquing the pinion nut is is the real beast part though - mainly...
  5. C

    Diff bearing replacement - shim location (and pinion shaft length?) change in 2014?

    If anyone stumbles across this thread in the future, let it be knowns this is a very involved job. Crikey! Hard with a lift, just utter ***** on your back with jack stands. I'm not going to brag like some youtuber that I did it in X hours. Straight dope - it's taken me a lot of time (plus...
  6. C

    Diff bearing replacement - shim location (and pinion shaft length?) change in 2014?

    I did look at some videos about those after seeing your post - was curious what they did differently, and you're right - I wasn't understanding how it worked. This youtube video does a really good job of explaining and showing the details of how it works and where it's engaging. It actually is...
  7. C

    Diff bearing replacement - shim location (and pinion shaft length?) change in 2014?

    I saw one video where a guy used that style and I think it worked for him. Now I see that listing it looks like it's very specific and very close fit to the particular bearing probably - so that outer shell holds all the pieces together from blowing apart when you are actually pulling on the...
  8. C

    Diff bearing replacement - shim location (and pinion shaft length?) change in 2014?

    Don't bother trying to use a puller to get the cones off the pinion and 2 carrier bearings. No chance - especially with this no-shim-there-so-no-gap-for-puller config. Cut the cage and rollers off with a grinding wheel (easy). Then put a deep cut with a grinding wheel in the bare race itself...
  9. C

    Diff bearing replacement - shim location (and pinion shaft length?) change in 2014?

    One bit of good news - the part came in and is the correct replacement shim I need - so the parts diagram in the Mopar system is wrong for these years - I guess they figured it was close enough and you could figure it out. Now I get to see if I can get it back together right.
  10. C

    Diff bearing replacement - shim location (and pinion shaft length?) change in 2014?

    I was thinking that at first, but this shim is very thick - probably 0.050 thicker than those in other spot. So you would have to crush the crush sleeve an extra 0.050. 200ft lbs crushes it about 0.015, so that's like 5x as much work. Watch the videos of guys tightening up that crush sleeve...
  11. C

    Diff bearing replacement - shim location (and pinion shaft length?) change in 2014?

    Yeah that's the crazy part. The only place I found confirmation that mine's not mixed up (other than I bought the truck new in 2014) is the service manual shows it in the right place. In total contradiction of the diagram in the parts manuals, and every youtube video or guide I've found. I...
  12. C

    rear Diff Whine- Maybe?

    I ended up buying this "Steelman ChassisEAR" thing for $100 that has 6 mics on cllps that you put all around the diff and axle, then run the wires to a switch up in the cab with you while you drive and listen with headphones to the different channels. Tracked my whine down to the pinion bearing...
  13. C

    Bad bearing in the rear diff. Swap the factory LSD to a trutrac while in there?

    Good call! I'm in the middle of rebuilding mine and there's a lot of confusion around the 2011+ models with the ZF - they changed the pinion shimming operation, and it's not correct for these later models (my 2014, your 2015) in any of the youtube videos I've watched. If you found a dealer...
  14. C

    Diff bearing replacement - shim location (and pinion shaft length?) change in 2014?

    Oh and spoiler alert - if you drive you're pinion bearing cup out with a chisel or air hammer like all the videos show - on the 2014+ you will be mangling that shim. Pre 2014 you're just hammering on the old cup which doesn't matter. So use a soft drift or something, or just plan to buy a new one.
  15. C

    Diff bearing replacement - shim location (and pinion shaft length?) change in 2014?

    I'm in the middle of rebuilding (bearings only) my 3.92 rear end on my 2014 1500. Apparently around 2014 they moved the pinion shims from the shaft (between gear and cone) to the housing (behind cup). It is also MUCH THICKER - mine is 0.067". The rebuild kit I got does not include that...

Members online

Forum statistics

Threads
213,355
Posts
3,092,145
Members
174,575
Latest member
DITRIO
Back
Top