Recent content by Dillonjm

  1. D

    M² Mods Intro & Project List

    Looking for a 911 bypass cable, how can I order one from you guys? Thanks! Sent from my SM-T280 using Tapatalk
  2. D

    How To Add Heated/Ventelated seats and Heated Wheel to Express/Tradesman

    Post #1490 I show which settings in AlfaOBD you need enabled to get the heated/vented seats to function. Connect to your MX in Alfa, the settings are in the body computer. Hope this helps
  3. D

    How To Add Heated/Ventelated seats and Heated Wheel to Express/Tradesman

    Gents. Success! Swapped over to the 7 speed bezel, module, and resistor and the seats work! Thanks for all the help
  4. D

    How To Add Heated/Ventelated seats and Heated Wheel to Express/Tradesman

    Removed the infotainment harness completely and plugged the 8.4 in direct to the truck. Still same symptoms. Hoping you guys are right and the addition of the 7 speed hvac module, bezel, and harness is the cure.
  5. D

    How To Add Heated/Ventelated seats and Heated Wheel to Express/Tradesman

    Thanks for the offer. I planned on converting anyway as I don’t like the cheap volume knob that comes with the infotainment bezel. Just gotta figure out where to source parts.
  6. D

    How To Add Heated/Ventelated seats and Heated Wheel to Express/Tradesman

    Looks like it’s time to order the new bezel and fan parts. Thanks guys! I’ll report back.
  7. D

    How To Add Heated/Ventelated seats and Heated Wheel to Express/Tradesman

    No, it still has the 4 speed fan and bezel. Not sure how far along you’ve followed so here is what is baffling me. I start the truck and turn on the seat vents on high. The seat fans will run, I can hear the seat vent system working (in both seats). Then after 15 sec it will power off and...
  8. D

    How To Add Heated/Ventelated seats and Heated Wheel to Express/Tradesman

    I added. It’s an infotainment piece from before I knew anything about Alfa. Follow on question. Is the 8.4 required for the heated/cooled seats? I removed the radio and put in my stock radio for diagnostics and the switch panel wouldn’t even light up when I pushed the buttons.
  9. D

    How To Add Heated/Ventelated seats and Heated Wheel to Express/Tradesman

    So did some more diagnostics and wire diagram tracing today. I’m starting to think that I’m missing something on my tradesman that I need to establish communications to the CAN BUS system. As I look at the wire diagrams from the HSM to the truck, I see that it should connect to a door module...
  10. D

    How To Add Heated/Ventelated seats and Heated Wheel to Express/Tradesman

    Read my mind. I tried that too. Nothing. Thanks for the thought!
  11. D

    How To Add Heated/Ventelated seats and Heated Wheel to Express/Tradesman

    No luck on the new module. I’m to the point of wire tracing I think. Pulling down the schematics and will try and figure out if there is a short upstream of the heated seat module since this is doing it for both seats and for both heated and cooled functions I believe it isn’t a short in the...
  12. D

    How To Add Heated/Ventelated seats and Heated Wheel to Express/Tradesman

    Yes, I have the 8.4 radio. And yes I only turned on the driver side in those photos. I unplugged and reconnected all the plugs, don’t see any loose connectors. I turned the 4 codes off then back on again. Will give it overnight, but I don’t think this is the issue. I checked the BCM for...
  13. D

    How To Add Heated/Ventelated seats and Heated Wheel to Express/Tradesman

    I don't see an ECU5, below are what I have enabled:
  14. D

    How To Add Heated/Ventelated seats and Heated Wheel to Express/Tradesman

    U0147-Lost comm
  15. D

    How To Add Heated/Ventelated seats and Heated Wheel to Express/Tradesman

    Cooled on then heated on:
See more

Latest posts

Staff online

Members online

... and 21 more.
Total: 1,217 (members: 71, guests: 1,146)
Robots: 1,288

Forum statistics

Threads
195,396
Posts
2,869,708
Members
156,061
Latest member
DirtyDan96

Share this page

Top