Recent content by gapi
-
Front Hellwig Sway Bar Install
Oh man! I put these on my 2005 Silverado ECSB Z71 (not lifted, stock size tires) and WoW, where had they been all my life. I could tell just making the turn out of my driveway. It does not make it a sports car for the track but helps on long clover leafs if you want to push it. I cheeped out...- gapi
- Post #19
- Forum: General Discussions
-
AlfaOBD
We purchased a used unlocked Trackhawk PCM and want to write the receiving vehicle's VIN to it. Is this possible?- gapi
- Post #13,972
- Forum: 4th Gen DIY
-
Keep the Chrome or complete Blackout
Black-out is so played out. Black wheels, "if" they look good or OK its only when the vehicle is sitting still and viewed in close proximity. Other than this when moving or from any kind of distance they look like dirty brake dust wheels. Just my 2¢. -
AlfaOBD
No, just swapping out a bad Module for a new one or a used one, is there VIN numbers to be considered, What is the initialization doing?- gapi
- Post #13,828
- Forum: 4th Gen DIY
-
AlfaOBD
When changing an ABS module does the Vin have any play in the procedure? Is this what the initialization does. Thanks,- gapi
- Post #13,826
- Forum: 4th Gen DIY
-
AlfaOBD
Our Charger has an open differential and of course traction control. What happens if I enable this line? ELSD Electronic Limited Slip Differential: Not set- gapi
- Post #13,285
- Forum: 4th Gen DIY
-
How-To: 4th gen hemi cam installation
I wonder if the previous party didn't know enough how to bolt down that rocker bar according to where the cam lobes were positioned. One needs to pay attention and know a lifter can be pumped and stubborn some times. You gotta work it accordingly, you can bend that tube. Also that hole in the...- gapi
- Post #163
- Forum: 4th Gen DIY
-
How-To: 4th gen hemi cam installation
No, the angle of the push rod onto the rocker keeps it located against the square washer on the tube. Slack may have let your push rod come out of the socket enough to be pushed by the socket lip and bend? Bad lifter, cracker spring?- gapi
- Post #159
- Forum: 4th Gen DIY
-
-
Fumoto valve?
They take too long to drain. If you don't mind that the principle is good.- gapi
- Post #74
- Forum: Engine & Performance
-
How-To: 4th gen hemi cam installation
Hi Guys, We know coolant gets into the oil system pulling heads..... I would like to know if you had to deal with oil in the coolant. I may have missed it in this thread. Was it mentioned?- gapi
- Post #140
- Forum: 4th Gen DIY
-
-
AlfaOBD
The search isn't getting me an explanation of what Special Package is or its intent anyway? Is it strictly splash and Logo displays?- gapi
- Post #11,802
- Forum: 4th Gen DIY
-
AlfaOBD
@Jimmy07 Have you finalized this experiment? If so I would like to hear about it and see your numbers. When backing out of a garage the Auto lights are on and the reverse cam screen is dimmed accordingly and cannot be viewed in a sunny cab until the auto lights go to off. I would like the...- gapi
- Post #11,671
- Forum: 4th Gen DIY
-
AlfaOBD
Well, (on the charger) I tried every NAV lockout related setting I could find and hit the security wall. Its a 2013 R/T and I'm hoping the security system is the same as with the trucks and can be defeated. We used a OBDLing MX+ interface.- gapi
- Post #11,548
- Forum: 4th Gen DIY
