Recent content by haleme
-
Cargo camera install
I just wrapped up my cargo camera install using the harness and guidance from Grimm. Put the smallest diameter camera I could find directly into the CHMSL and then cabled to the radio. Also replaced all three lights with LEDs to keep the heat in the stop light area down. Easy as that. Side...- haleme
- Post #16
- Forum: 4th Gen DIY
-
Wire Terminal Connectors and other doodads
Added more stuff and increased the size of the box. -
Ordering a No Splice Kill Switch Harness
I have had the KS harness installed on my 2500 for about a year now. Works flawlessly every single time. I don't use a switch to kill the start button, but an RF transponder and receiver attached to the KS harness. No buttons or switches are present in the truck for a thief to button mash and...- haleme
- Post #38
- Forum: JW2 Innovations
-
-
Wire Terminal Connectors and other doodads
Duh, thank for the reminder. I was inspired by the "Pay It Forward" Box thread. -
Wire Terminal Connectors and other doodads
Upping the ante here. Since I am done with the projects on my truck and camper, I have found more items to clear out of the shop. All still FREE; just pay for USPS medium flat rate box postage of $18.40 Various terminal connectors from 10 to 16 gauge Lots of wiring of various color, gauge and... -
SOLD - Bottom button panel for a 4th Gen
Sorry about not replying. Was not getting notifications on this thread. PM sent to tilemaster. -
What did you do with your 4th Gen this week?
Had three left over LED lights from my RV and installed in the bed. I made my own harnesses and plugged them into the factory bed lighting. The new lights are controlled by the dash and bed switches.- haleme
- Post #44,031
- Forum: General Discussions
-
Additional UAQ/UAS Update Files 28.3/30.24/34.2
After the screen didn't turn on during the upgrade to 28.3 (new anxiety unlocked), I'm just thankful it has worked every time since the last upgrade to 40.1. -
Wiring aftermarket led bed lights to dash switch
Do you already have factory lights in the bed?- haleme
- Post #2
- Forum: Audio & Electronics
-
Additional UAQ/UAS Update Files 28.3/30.24/34.2
I have reset the navigation volume to 10 a few times and every time I start the truck, the volume is set to 15. I enabled to Off-road Capable and Pages and the screen never showed up. Another confirmation it was removed from 40.1. -
What did you do with your 4th Gen this week?
Added USB outlets to my upper glove box this week.- haleme
- Post #43,982
- Forum: General Discussions
-
Additional UAQ/UAS Update Files 28.3/30.24/34.2
Not having an issue with the XM presets. But the GPS guidance volume is still always set to 15, so I just have it muted by default. I also noticed the map view inside the media screen is reformated and everything is much easier to read. -
Additional UAQ/UAS Update Files 28.3/30.24/34.2
Did the updates last night. After updating to 28.3, the screen went blank and would not turn back on. Everything worked and the touchscreen was still responding, changing channels on the radio, but no visual. I figured that starting the update to 40.1 would send a reset to the radio and... -
Additional UAQ/UAS Update Files 28.3/30.24/34.2
I found it in UCONNECT_8.4_UAQ_IR21.9_MY18.
Members online
- Balto171
- HemiLonestar
- Scout51
- lkmiller
- neboysa
- OtisM
- Black-Wolf
- Kermudge
- MethrenUnede
- RebelDad
- Yardbird
- Reb87
- Motoman501
- RamDiver
- Rebel Guy
- Fritter
- Lsujker
- StateOfMind
- jayquelin
- DanZ
- Ramv
- Curmudgeon
- MOPAR78
- Scott Webb
- Tom Davis
- Hardracer
- Kootbiker
- Daw14
- Audiowriter
- Wallyb4
- ToxicFire
- Dodge Racer
- GrangerMotors
- Akaras3
- hunterdan
- Jchris56
- enuser
- biner
- duckman631
- jeff_rey
- TC
- Dr Lecter
- karlbtx
- adams5
- Jeepwalker
- Renegade17
- tron67j
- Gwlangston
- ragarm33
- nlambert182