Recent content by HangmanNY

  1. H

    Locking gas cap

    Is there a definitive answer on whether siphoning cannot be done on these RAM trucks? I have a 2015. We do spend some time in Florida. Just checking the message board down there and there have been a rash of fuel tanks being siphoned dry.
  2. H

    Transmission pan and fluid change questions

    I sent Jessie a private message. I don’t feel comfortable doing it myself but I wouldn’t mind paying someone to do the work with his kit. Providing that everything will work as people claim. We are between North/central Western Florida and downstate New York. I don’t know if any of the...
  3. H

    Transmission pan and fluid change questions

    Right. Is we are between Long Island, NY and Florida. Hopefully in Florida permanently by the end of this year. have some of the guys here has good results with the RevMax bypass kit? Are there any detailed videos showing how this is done? And what were the resulting transmission...
  4. H

    Are these “normal” operating temperatures?

    I have a 2015 Ram 1500 with the 5.7l hemi and the ZF 8HP70 transmission. Just over 90,000 miles. I did both differentials fluid changes with Redline fluids, transfer case with Amsoil MV atf. I also removed the Mopar factory transmission pan and put the PPE pan in. I went with the Valvoline...
  5. H

    Transmission pan and fluid change questions

    *
  6. H

    Transmission pan and fluid change questions

    Yesterday I drained the cooling system. Then removed the original thermostat, cleaned all surfaces, put the rubber ring back in and put the bolts back in. Then refilled with distilled water and a quart of flush. I drove it for @ 70 minutes, drained, filled again with distilled water, drove...
  7. H

    Transmission pan and fluid change questions

    I took all of the spacers out of the PPE pan. Then I took them to the bench grinder stone wheel. I took about an eighth of an inch off of one side. Then cleaned them up with the wire wheel. Then I put them on a couple of flat files to finish them off. Now they fit the height of the holes...
  8. H

    Transmission pan and fluid change questions

    Did you notice if the spacers were longer than the thickness of the PPE pan?
  9. H

    Transmission pan and fluid change questions

    Do you think I should remove the spacers or leave them? It was a struggle getting them in the first time. The holes in the PPE pan are a hair smaller than the factory Mopar spacers. I had to clean up the holes a bit. I even cleaned the spacers on a bench grinder wire wheel then gave them a...
  10. H

    Transmission pan and fluid change questions

    I received the new 1/4” CDI torque wrench a couple days ago. I also bought another new gasket for the PPE transmission pan. I’m waiting for a new set of pan bolts which should arrive tomorrow I know the old torque wrench was the problem. However the spacers were flush with the gasket side...
  11. H

    Transmission pan and fluid change questions

    I have been buying a lot of tools bit by bit for the past few years, including a lot of Knipex pliers. Those Japanese pliers have a specific purpose and they are worth their weight in gold when that situation arises. The company is called “Engineer” . Those pliers are called “Neji-saurus RX”...
  12. H

    Transmission pan and fluid change questions

    Which fluid are you using? I used the Valvoline MaxLife after reading numerous reviews and watching videos online.
  13. H

    Transmission pan and fluid change questions

    Let me ask a hypothetical question. Is it normal protocol to use a new set of transmission pan bolts when changing the pan or servicing the filter? Because when I took the original pan bolts out some of them had a little bit of corrosion. I put them on the bench grinder wire wheel and cleaned...
  14. H

    Transmission pan and fluid change questions

    I have three torque wrenches. All from harbor freight. 1/2 inch & 3/8” are the Icon brand. They don’t have a 1/4” torque wrench, only the Pittsburgh brand. That’s what I used. I don’t like this thing and it’s going back. It has a dial on the bottom which is supposed to lock the setting in...
  15. H

    Transmission pan and fluid change questions

    Engineer Neji-saurus RX. Model PZ59
See more

Latest posts

Staff online

Members online

Total: 1,085 (members: 50, guests: 1,035)
Robots: 1,578

Forum statistics

Threads
195,439
Posts
2,870,291
Members
156,143
Latest member
BillMorehouse

Share this page

Top