Recent content by jcsmith

  1. J

    Fuel level sensor

    I have an '05 1500 3.7 , 35 gallon tank. Have code P0463. Does anyone know if the fuel level sensor is available separately. Can't seem to even find a part number. Appreciate any help. Chris
  2. J

    2014 Ram 3500- 5.7 Hemi- Very Frustration Heater Fan Issue- Intermittantly Working

    Did you get it fixed? I had the same problem. Turned out to be burnt contacts on ignition switch on left side of steering column. Tilt wheel action would cause it stop or start working. Chris
  3. J

    Turn signal issues, not TIPM related

    I was just reading a thread on 3rd gen Technical Service Bulletins and one mentioned this very issue. It said to replace the multi function switch. Chris
  4. J

    Are All Three Bulbs the Same??

    My 05 1500 has 3 3057's also
  5. J

    c e l is on, solid, but code reader does not detect any codes

    You can read engine codes right off your dash.You can also get total engine hours, do a gauge cluster check and get c codes.
  6. J

    AC button light flashing

    On my '05 1500 the light on the AC button is flashing. I had to replace the ignition switch recently because the blower fan was acting up. Everything was fine for a while , but when tilting the steering wheel occasionally the blower would stop.The wiring harness plug that plugs into the ignition...
  7. J

    HVAC recirculation door actuator calbration

    All is good with the recirc door functioning properly. The door was broken when I bought the truck. Just got around to replacing the door. I was able to replace the door thru the hole where the blower mounts. It was tricky .I got a Dorman door that had the metal doohickie instead of the white...
  8. J

    HVAC recirculation door actuator calbration

    Had to replace recirc door on my 2005 1500. The actuator is in place , but the door is half way between recirc and outside air. Does it calibrate itself when power is connected ? Appreciate any help. Chris
  9. J

    Blower Motor turns off/on intermittently

    I had the same problem . Turned out to be the ignition switch . Apparently a bad design. The contacts get burnt over time. I replaced the switch , which cured the problem , but the wiring harness plug was burnt also so the problem is back. Not getting a tight connection. So I will put a relay...
  10. J

    Turn signals acting up

    I appreciate the response. The headlights are stock replacement with halogen bulbs.
  11. J

    Turn signals acting up

    Recently I installed new aftermarket headlights. With headlights off the turn signals operate properly. The flashers work correctly also. But, with headlights on the turn signals flash fast and the bulb out message flashes on the dash. Four ways work normally tho. Does anyone have any...
  12. J

    HVAC fan switch

    Update; turned out to be the ignition switch on the left of steering column. Not the key tumbler. The contacts get hot and burned raising the resistance , and losing contact.This might help someone in the future. I was able to remove the shroud around the column and wiggle the switch , which got...
  13. J

    HVAC fan switch

    The switch was working on all speeds so I assume the resistor was good, but electrics are not my forte
  14. J

    Riveted front lower ball joint

    I know this is an old thread. The rivets hold the forged end piece to the control arm. You just grind what looks like a weld bead , and press the ball joint out.
  15. J

    HVAC fan switch

    I appreciate the response. I will give it try. Chris
See more

Latest posts

Staff online

Members online

... and 9 more.
Total: 1,577 (members: 59, guests: 1,518)
Robots: 1,607

Forum statistics

Threads
195,474
Posts
2,870,713
Members
156,189
Latest member
budaBing

Share this page

Top