Jmarks91
- Posts
- 12
- Reaction score
- 5
Latest activity Postings About
-
-
Jmarks91 replied to the thread 2014 ram 1500 5.7 misfire and ignition coil C secondary circuit p2308 p0303.I was by myself the whole rebuild and yes I babied the harness I actually followed it down and realized it was a loose/dirty connection... -
Jmarks91 replied to the thread 2014 ram 1500 5.7 misfire and ignition coil C secondary circuit p2308 p0303.Yes it runs and drives but rough idle and slight power change
-
Jmarks91 posted the thread 2014 ram 1500 5.7 misfire and ignition coil C secondary circuit p2308 p0303 in General Discussions.I recently replaced my cam , lifters , rods , and plugs as well as the MDs delete I am getting a p0303 cylinder #3 misfire code as...
-
Timing doesn't have to be 180 out to bend pushrods,if you're a tooth r e t a r d e d,it'll bend push rods,biggest mistake you made was...
-
Hi there, Our team would recommend bringing this to your dealer's attention. If you decided to do so, feel free to send us a private...
-
Sounds like the cam timing was 180 degrees of, how did you line the timing gears up?
-
Jmarks91 replied to the thread ram 1500 hemi issue.i was assuming the crankshaft gear mark was still at the bottom so i lined the top up with the mark on the phaser in between the two...
-
whats up yall i recently did a lifter and cam swap due to failed lifters on my ram 1500 hemi, i aslo did the mds delete as i put...
-
whats up yall i recently did a lifter and cam swap due to failed lifters on my ram 1500 hemi, i aslo did the mds delete as i put...
-
What’s up guys I just recently did a cam and lifter job on my 2014 ram 1500 hemi I have everything back together with the exception...
-
Jmarks91 replied to the thread Lovely lifter tick.It is constant it doesn’t go away
-
Jmarks91 replied to the thread Lovely lifter tick.That’s what I’m scared of happening
-
Jmarks91 replied to the thread Lovely lifter tick.I wish I could post a video of the sound
-
Jmarks91 replied to the thread Lovely lifter tick.It is definitely a lifter it is not throwing a code yet The only code I have is from the fuel level sensor The bad thing is I have a...
-
Yes. Then start reading this thread,and watch a couple video's,i think MMX has a decent video out...
-
-
Loading…
-
Loading…
Staff online
-
G-Ride990Administrator
Members online
- mikson
- bonnyjliss
- Looniaser
- saturnx
- Chris57ram
- eleighty
- DSessom
- bucktruck
- max2bob
- akguy09
- sraiders00
- rickjkline
- Fast69Mopar
- Daw14
- star_deceiver
- stevieb92
- Jsimon34
- 09SilverRam
- jawzs2
- Dredger
- xVXx
- G-Ride990
- Wild one
- DaveInHSV
- retrac
- McTylerMore
- Bmags
- Heatstud
- RamDiver
- CensoredK14
- cola tech
- FJ Mike
- ethov8
- hdog33
- 2020GCM
- Blazerman
- Chukbacca
- Brian1959
- JayLeonard
- minotto
- Wmickelson
- Dean2
- Ramfanski
- Martas4444
- Esmeraldostvb
- Yardbird
- bryanmoore59
- shmedley
- turkeybird56
- PA Ram