Recent content by Jose Zambrano
-
Boost a Pump install, which is the Fuel Pump Power wire?
I got a few questions, I recently installed same supercharger and I'm getting ready to do the boost a pump install. Is there anything I should watch for, or any tips you might have. Also where did you end up putting the head unit at? I'm trying to decide where I want it or where would be the...- Jose Zambrano
- Post #30
- Forum: Engine & Performance
-
Cold misfire with a few codes ( P0300, P0456, P0175 )
Have you checked for any vacuum leaks or anything like that, I have the same issue but mine does not throw any codes. Mine will stutter a bit at cold start then it will level its self out after about 10 seconds. My tuner said it could be a vacuum leak or a bad gap on one of the spark plugs. I...- Jose Zambrano
- Post #2
- Forum: Engine & Performance
-
345 vs. 392
One other thing why most people use the 5.7 instead of the 6.4 is because the 5.7 does better with boost applications than the 6.4 engine.- Jose Zambrano
- Post #12
- Forum: Engine & Performance
-
Moes
Moe's is closed till April I believe, Matt is not taking any new orders at the moment.- Jose Zambrano
- Post #8
- Forum: Engine & Performance
-
Upgrades for everyday driver
I daily drive my truck and I take it to the track so hopefully I can give you some input. Like most have told you already, throttle body spacer is a waste of time and money. I would suggest start with the a custom tune first, that's where you will see the better gains and you will need it to see...- Jose Zambrano
- Post #12
- Forum: Engine & Performance
-
-
BATRAM project I need help from someone that its good with photoshop
Well I'm turning my truck into the BATRAM dark knight edition and slowly but steady I've been making improvements on it. Sometime next year I'm either going to be doing a paint job or wrapping the truck. I need help coming up with a design for the exterior. My goal is to have the truck look as...- Jose Zambrano
- Thread
- Replies: 0
- Forum: Photoshop
-
What bolts for JBA headers?
No, I used a rust proof high heat paint on headers first, then I wrapped them after that I used a high heat silicone paint on the wrap to keep moisture away from the wrap.- Jose Zambrano
- Post #31
- Forum: Engine & Performance
-
Another question about grill shutters
Is there a reason why you don't delete the AGS system. Are you planning on doing the lower temp tstat as well? If you are it will just be a lot easier to do the AGS delete then trying to have the toggle switch.- Jose Zambrano
- Post #8
- Forum: Engine & Performance
-
2013 SLT Push Button Start and Remote Start
Hope someone can help so I'm in the same boat. I have a 2014 that I want to upgrade to push to start and since I'll be doing that I'll do the remote start as well. My Rf Hub according to the alfa obd is ECU part number: 68213675AH, Hardware number: 68213675AE. Now when I looked at the hub itself...- Jose Zambrano
- Post #11
- Forum: All Mopar Parts
-
What bolts for JBA headers?
I've had my jba on for about a year with the bolts that came with the headers, I used the oem gasket for the 6.1 gaskets, I've heard remflex is the way to go but I have not had any issues with my gasket at all. I also think you should wrap them, at first I didn't wrap mine but after 6 months I...- Jose Zambrano
- Post #28
- Forum: Engine & Performance
-
Keyless Remote Programming
Finally found one about programming the push to start lol. I have a question once you go select Highline system and go through the instructions in the app. Do you have to wait the 5 minutes or are there any additional steps after that. Also do you need to have one original key with you inside...- Jose Zambrano
- Post #8
- Forum: Audio & Electronics
-
Performance Modifications
Yeah there is a few parts that won't void your warranty, but also buying everything with time and not all at once is very helpful on the wallet lol- Jose Zambrano
- Post #123
- Forum: Engine & Performance
-
Performance Modifications
You can do a tune on it, you can reset it back to stock when ever you have some warranty work being done. That will wake up your truck the most.- Jose Zambrano
- Post #121
- Forum: Engine & Performance
-
Aftermarket Hood
If you are still thinking of replacing your hood, amerihood is the best option as far as any fiberglass goes. Its very solid and I've heard a lot of people run it without any pins mainly because its of good quality. I purchased one that was used and luckily it was the same color as my truck. Fit...- Jose Zambrano
- Post #13
- Forum: Exterior
