Recent content by MayerMR

  1. MayerMR

    4.7 l problems

    I'd call you a glutton for punishment swapping engines left and right like that. But to answer your question - no, I didn't bore it out. I just honed the cylinders is all. As far as connecting rods goes - are you building anything special or just doing a rebuild? If you aren't building for...
  2. MayerMR

    OEM/Factory Radio No Workie...

    Well, I checked the harness today over lunch and didn't find any fuse going into the harness where that other thread indicated. I'm thinking there may have been some changes between 2005 and the 2010+ trucks. I appreciate the lead though!
  3. MayerMR

    OEM/Factory Radio No Workie...

    Thanks for the reply. I saw that thread already but discounted that as a possibility when I saw it was for a 8.4 system since mine is much older and had a tape deck. But you're prob right. I should look for that fuse anyway.
  4. MayerMR

    02 4.7 ground strap behind head

    It's not attached in the firewall. I just finished putting a 4.7L engine in. The far end of that braided cable attaches to one of the 10mm studs on the underside of the transmission tunnel on the passenger side above the exhaust down pipe.
  5. MayerMR

    OEM/Factory Radio No Workie...

    Hey fellas, I'm in the process of "restoring" a 2005 Ram 1500 SCSB truck that I picked up with a blown motor. Now that I've replaced the motor with one I rebuilt and got it running great, I'm starting to try to delve into some of the other issues. The foremost issue for me right now is the OEM...
  6. MayerMR

    4.7 l problems

    when I just rebuilt a 4.7L that had 180k miles on it, every piston had at least one stuck ring, if not all of them stuck in their grooves. I struggled to get them out. But I was replacing the pistons in the rebuild so I didn't try too hard. Not sure what you could do to try to get them freed up...
  7. MayerMR

    '05 3.7L Overheated & Seized - What to do next?

    You are 100% right, the guy I got the PCM/harness/etc from (who I am meeting tomorrow to get the ABS module) is having a hell of a time going from the 4.7 to the Hemi. He's got it running, but the truck has so many codes it's driving him nuts. The transmission is in limp mode, the ABS module...
  8. MayerMR

    '05 3.7L Overheated & Seized - What to do next?

    Well, my ******** was right, the high-idle was caused by the open port in the rear of the intake that is meant to be attached to the PCV. What a COMPLETE and utter pain in the rear to get to though - I had to completely remove the intake to get to it. Pain in the butt. It did fix the issue...
  9. MayerMR

    '05 3.7L Overheated & Seized - What to do next?

    Ahh, I think I may have figured out my high-idle issue - I did a search on high-idle issues with a 4.7 and it appears a leaking PCV hose may cause the high-idle condition. Well, I had not yet figured out the routing of the PCV, so it's just sitting there, open-ended. So yeah...duh. I'll try to...
  10. MayerMR

    '05 3.7L Overheated & Seized - What to do next?

    Well more good news! The new oxygen sensors arrived today and they cleared the O2 codes. I also bought some MAF spray cleaner and sprayed it on the sensor, which cleaned a lot of the soot/dirt from it. I figured that would clear the code. And it did, for awhile. I took it on a short drive and it...
  11. MayerMR

    Junkyard block

    Not sure, I've never been to San Antonio. I just saw that they had a location in San Antonio when I was looking up their services on their website.
  12. MayerMR

    Junkyard block

    Hey you're a lucky guy - there is another branch location of City Motor Supply in San Antonio, TX. I'd go there. Also, see my note in the private message response I sent to you - if you have a decked head on that 4.7L, then you may need to run pistons with a reduced crown. Best make sure you...
  13. MayerMR

    Any AC guru's in here?

    Don't rule out that it's low without checking. I completely replaced my entire A/C system in my '87 Jeep Wagoneer XJ and less than a year later I was getting the same issue. Defect in the refrigerant line crimp allowed it to slowly leak down over time. I'd put money down that you're low on...
  14. MayerMR

    The Strangest Leak I've Ever Seen!

    Is it oil residue? Try cleaning it with acetone and seeing if it returns.
  15. MayerMR

    Junkyard block

    I agree, that shop is being ridiculous. I assume you'll be using new wrist pins as well new rod bearings, why they hell should they care? Or just send them to City Motor Supply in Dallas and they'll do it for you for $92 out the door with a 1 day turnaround.
See more

Latest posts

Members online

... and 29 more.
Total: 1,454 (members: 79, guests: 1,375)
Robots: 1,521

Forum statistics

Threads
195,564
Posts
2,871,942
Members
156,331
Latest member
33hemi

Share this page

Top