Recent content by mpittman
-
VHT Nightshade for taillights
1. Remove light from truck 2. Mask off the reverse light (optional) 3. Scuff the original factory finish with 600 grit sand paper. This will leave a dull finish. 4. Clean light with alcohol, removing all finger prints, sanding dust, and contaminates 5. Spray 2 or 3 light coats of VHT or other... -
VHT Nightshade for taillights
I plan to tomorrow. Sent from my iPhone using Tapatalk -
VHT Nightshade for taillights
One guy I know used the same products and process, and he’s going on 4 years of looking like new. So, we’ll see. Sent from my iPhone using Tapatalk -
VHT Nightshade for taillights
I know lots of people are not a fan of this, but I think it looks great. First attempt ever. 3 layers of VHT 4 layers of clear 1500 grit wet sand Meguiars compound with a Harbor Freight DA Polisher Meguiars Polish Meguiars wax Sent from my iPhone using Tapatalk -
Headlight condensation 10 minutes after brand new install
I did not buy aftermarket lights, I broke my OEM lights open and rebuilt them. After putting it all together, I ran through a car wash. Only one of my lights fogged up. Turned out, I forgot to put one of the dust caps back on. I put the cap on, and no problems since. Sent from my... -
Zone 4" lift with bilsteins?
Looks really good! I like that stance. Sent from my iPhone using Tapatalk -
Zone 4" lift with bilsteins?
I see two rings exposed on mine, and I’m at 1.4” setting. I see one ring exposed on yours, so that should be the 0.7” setting. That first ring would be 0” factory height. Sent from my iPhone using Tapatalk -
Zone 4" lift with bilsteins?
True.... maybe he got the 4/2 lift by mistake? Sent from my iPhone using Tapatalk -
Zone 4" lift with bilsteins?
As someone else mentioned... the spring seat may be on upside down. That would raise it a little. Sent from my iPhone using Tapatalk -
Zone 4" lift with bilsteins?
Looks great! Here’s mine. Sent from my iPhone using Tapatalk -
Zone 4" lift with bilsteins?
My shop was a little perplexed about the bilstein lift as well. That’s exactly why I set them myself. I just know our setups sound really similar and I’m dead level with Bils at 1.4”. Most people are with a 4/3 lift. Sent from my iPhone using Tapatalk -
Zone 4" lift with bilsteins?
Did you set the Bils yourself? I got a 4/3 BDS lift with Bilsteins at 1.4” I’m dead level in all four corners. I didn’t trust the shop to set my Bilsteins correctly, so I set them myself and told the shop not to touch them. They were an authorized BDS installer, so I did trust them with... -
Headlight Retrofit Progress!
Here is my video: Sent from my iPhone using Tapatalk -
Getting flashed after my 4" lift
I had no idea where to aim my lights. So, I used my Dodge Journey as a guide. I set my Ram lights to the same height at 25 feet out, then went for a drive. LOL.... I could barely see past the front of the hood. I came back and raised them up and just winged it. Took another drive. Met... -
Getting flashed after my 4" lift
This worked for my 2015 1500. There are two holes with arrows, mine was in the other hole than what this video shows. Shine a flashlight down in the holes and you'll see the adjuster.
Members online
- aszumilo
- Suma Performance
- Mike Flea
- fhc50cent
- keeponcummin
- teddy Charlery
- tzmndvl308
- jabartram
- Th3K1ng
- Atcer2018
- c85jl
- Craze82eny
- HydroTopzz
- Joe Wales
- Killsek
- Wild one
- crackerjack1957
- DontdodgeRam-em
- DeckArtist
- Hootbro
- Houston1414
- RamDiver
- netshadoe
- FarmerFramer
- Bigfoots03hd
- 4x4RAM1500
- Mrsmith4
- mrack
- hdog33
- Heathen-19
- MThompke
- corneileous
- Swims43
- 1500farm
- bbykes
- Rlaf75
- Lsujker
- shakey32
- Chicoblanco
- pendragon97
- whitness