Recent content by swoyekr
-
S
Laramie Interior Handles
As info, i got around to wiring up my jumper harnesses today and got everything installed. 1. I was able to activate pins 3 and 9 with alpha obd on my 2013 ST base model truck. Under BCM, Configuration change and then searched for LED's and the last two were door handle and map light. 2. I... -
S
Laramie Interior Handles
As info, I'm getting ready to do this swap in a week or so on my 2013 st Diesel 2500. I was able to get all the pins per deereguy's post and ordered from mouser, will make my own harness and program per this thread. The rears, I just ordered the harnesses for my year truck. As info for anyone... -
S
Laramie Interior Handles
I just checked my door harness and I'm missing pin 4 - footwell lamp and pin 6 - Passive entry in my body connector side. Does anyone know where to grab the footwell lighting or does the whole truck harness need to be replaced back to the BCM? I guess I can just use deerguy's wiring... -
S
Laramie Interior Handles
Are you saying you pulled the OEM harnesses from a limited truck, reinstalled in your truck and programmed and everything workeD? This is what I was planning on doing, it's about 60 bucks per door harness and LB2 appears to be the sales code, at least for the rear. I was worried about it needing... -
S
How to Add Automatic Temperature Control (ATC) to a Manual Temperature Control Truck
Sorry for the delayed response; HU ID 0x395E9A22 Software Part Number CNSC27N5GL Software Version 17.43.44 Application Version USA-IR-19.9.0-20171026-107G BootMicro Version 17.35.00 I will update the HVAC Module Firmware here tomorrow. I checked the light sensor under the middle speaker...- swoyekr
- Post #992
- Forum: 4th Gen DIY
-
S
How to Add Automatic Temperature Control (ATC) to a Manual Temperature Control Truck
Man, I've tried fooling my 8.4 to accept the single auto climate controls about 20 times. It seems like everything goes well, but the climate control up/down buttons and the slider on the radio just move to max hot or max cold.. If i move the slider to 82*, it just thinks for a second then...- swoyekr
- Post #990
- Forum: 4th Gen DIY
-
S
How To: 13-14 premium cluster upgrade
I've recently started grabbing these when I can to resell on ebay. If someone looking for something specific let me know I'll see what I can find for you.- swoyekr
- Post #938
- Forum: 4th Gen DIY
-
S
Only one overhead light works
Only one of my map lights in the overhead console doesn't work, it's a 2013 2500. I thought it was just the bulb but changing that didn't do anything, I ended up swapping to a LED with homelink over the weekend and the passenger side works fine but the drivers side still doesn't work. Any ideas... -
S
Uconnect 8.4 w/NAV to Uconnect 8.4 UAQ w/NAV - CarPlay
That's a Harman unit, they don't have car play. You need a 2018+ Pioneer.- swoyekr
- Post #4
- Forum: Audio & Electronics
-
S
P flashing on dash after gauge cluster swap
I had this happen when swapping a 17 gas cluster into my 13 diesel. I was told it was because of the transmission differences, 8 speed vs 6 etc. It was kind of annoying but ran fine. Switched to a 13 gas cluster and it went away, but so did half my evic gauges. Apparently, the 13 diesel clusters...- swoyekr
- Post #8
- Forum: Audio & Electronics
-
S
How To: 13-14 premium cluster upgrade
https://www.ebay.com/itm/265638730293?hash=item3dd94d5a35:g:9ywAAOSwTSJiVF9- Good price on a limited canadian cluster if anyone needs one.- swoyekr
- Post #933
- Forum: 4th Gen DIY
-
S
How To: 13-14 premium cluster upgrade
So I installed a 13 cluster, and now I have a new problem. The voltage, Fuel Filter, and TPMS are all blank. THe TPMS I'm not completely worried about because it worked initially but also didn't work on the old cluster, I believe the wheel units are the culprit there. However, the fuel filter...- swoyekr
- Post #931
- Forum: 4th Gen DIY
-
S
How To: 13-14 premium cluster upgrade
Thanks guys, I decided to grab a 13. Should have done my research.- swoyekr
- Post #928
- Forum: 4th Gen DIY
