Recent content by TheBeej
-
T
What nerf bars for a blackout edition?
I had the NFAB wheel to wheel on my '12 Crew Cab. -
T
Ram's with black rims
Here's my '13. I still need to do some polishing and a solid coat of sealant but her she is. -
T
Just ordered my drop....
Cullen17, You can cut the factory front springs to get the drop to 3" up front and cut the rear springs to get 4" out back. LHemi, Grats on the drop kit and post up some pics if you guys get the weather for the install. -
T
GForce 2/3 drop but wanting to go lower
LHemi, the drop was done by using both kits and the only pieces I didn't use from the 2/3 kit were the rear springs. Warmage, I haven't measured how far out they stick but it is very noticeable to me anyways. If I had to guess prob 1/2 to 3/4". Once the weather down here warms back up and I can... -
T
GForce 2/3 drop but wanting to go lower
Thanks! As for the wheels I was pretty iffy at first. I even considered trying to trade for some Slides, but it seems a ton of people run them or the SRT wheels. So now that the Sync's have grown on me I will be keeping them. Matt at Moe's hooked me up and the dod shipped out today! Hopefully... -
T
3/5 or 3/5.5 on 24
I'm running 285/45/22's on a 4/5.5 drop on a 13 crew. However, I do rub the front inner liners and the inner fender lip if I'm not paying attention to the bumps and dips in the road. -
T
GForce 2/3 drop but wanting to go lower
Not the greatest picture of all. I promise to post up some better ones once this TX weather goes back to normal. Specs so far: '13 Express Crew 22" KMC Sync's w/ 285/45/22 Tri-Flip Tonneau 5% tint all the way around w/ 5% brow VaraRam Drop is a combination of GForce 2/3 and McG's 2/4... -
T
GForce 2/3 drop but wanting to go lower
I ended up running the McG's 2/4 deluxe kit like suggested. So up front I currently have the 2" drop spindles with the GF 2" drop springs. Rear I used the 4" drop springs and cut 1.5 coils off. Also kept the GF drop shocks at all 4 corners, ride is fairly good however I hit the rear bump stops... -
T
air bags kit for 3/5 lowered
Did you cut out the factory bump stops? Most guys from what I have read cut the factory stops off and replace them with some from energy suspension or Belltech. Brandon -
T
GForce 2/3 drop but wanting to go lower
I just picked up a 2013 1500 2wd Crew Cab that the dealer installed a Ground Force 2/3 drop kit and 22" KMC Sync's. However after looking at some of the trucks in this section, I'd like to go lower. So I figured I would ask in this section to see what kind of options I have. I'll post up some... -
T
New Guy with a '12 2wd
Thanks for the Welcomes! Mostly lurk in the 4th gen section and as you can tell, I don't post much. Trup, what shop do you work in? I used to be down in the 50th from 00-05 & still come back from time to time. Have a ton of friends still there as well. Brandon- TheBeej
- Post #14
- Forum: Introduction
-
T
New Guy with a '12 2wd
Just thought I'd drop in this section and say hi. Name is Brandon and current ride is a 2012 Ram Express Crew Cab, 2wd, 2" Fat Bob's level and a 1.25" Rough Country BL. You guys are very bad for me lol! There are some very clean and amazing trucks on this site and in this section!! Anyways...- TheBeej
- Thread
- Replies: 15
- Forum: Introduction
-
T
Post your step bars/running boards?
I don't have any pics here, but I've got N-Fab 3-Step Wheel-to-Wheel bars. -
T
Lets see your bed covers..!
I'm running the Extang Revolution on my '12.
