Recent content by Tpearson515
-
More lift for a Warlock
Here is my 19 classic warlock with a 2 inch front kit 1 inch rear spacer and 1.5 inch body lift, On 35 12.5 20's, This is my second 4th gen ram I've done this to and very happy if you are on a budget, I also upgraded UCAs for peace of mind the stock ones worried me because there was separation...- Tpearson515
- Post #9
- Forum: Lifted
-
2019 classic warlock 1.5 body lift / level with oem tow hooks
Hey j-b for some reason I can't send a pm with a picture, basically here is how I cut my bracket kept notching it down until it fit then re used hardware with blue loctite, I dry fit everything first it may be different on yours, hope this helps!- Tpearson515
- Post #7
- Forum: Lifted
-
2019 classic warlock 1.5 body lift / level with oem tow hooks
Hey , looks great on 35s!, I think I have pictures I took, I always thought doing the body lift I wouldn't be able to use the tow hooks. After I got done with my install I tried to re install them and the hooks still lined up through the front holes, I took my original hardware slotted out the...- Tpearson515
- Post #6
- Forum: Lifted
-
2019 classic warlock 1.5 body lift / level with oem tow hooks
Hey, this is my second body lift on a 4th gen, both times took me around 4-5 hours to install, I did check all my harnesses everything looked great,- Tpearson515
- Post #4
- Forum: Lifted
-
2019 classic warlock 1.5 body lift / level with oem tow hooks
Just wanted to post here for anyone interested, I had been going back and forth on how I wanted to lift this truck up a little, long story short 2019 classic crew cab warlock Installed 2 inch top strut spacer, 1 inch rear spacer, 1.5 inch zone body lift d9150. My current from fender to ground...- Tpearson515
- Thread
- Replies: 8
- Forum: Lifted
-
Zone body lift instructions. Just ordered a kit
Hey Man, hope all is well! I remembered you had recently installed your body lift, I did one on a 2015 about 4 years ago now, I now have a 2019 classic warlock I'm putting one on, just did the level 2 weeks ago, and just orders the body lift! The only thing I can't quite remember is the front...- Tpearson515
- Post #56
- Forum: Lifted
-
4 “ ready lift on the 19 Warlock!
Your truck looks great, do you have any pictures of the CV angles or the sway bar drop bracket? Without the drop bracket in this kit will the sway bars rub? Sent from my SM-N975U using Tapatalk- Tpearson515
- Post #22
- Forum: Lifted
-
4 “ ready lift on the 19 Warlock!
I'm thinking of going with this ready lift route, my question is if I already have the rear suspension lift parts from another truck are you guys aware if any kits that include the ucas sway bar drop brackets and front spacers? I tried to contact ready lift to individually purchase the pieces...- Tpearson515
- Post #20
- Forum: Lifted
-
Under the rear wheel well liner
Thank you that does help and yeah it will be in the way, appreciate the help though! Sent from my SM-N975U using Tapatalk- Tpearson515
- Post #4
- Forum: Exterior
-
Under the rear wheel well liner
Does anyone know if you can reach the bottom side of the bed rail if you remove the rear wheel well liner, I have a small dent close to the top of the fender was just curious if anyone knew before I pull it off to check next week Thanks! Sent from my SM-N975U using Tapatalk- Tpearson515
- Thread
- Replies: 3
- Forum: Exterior
-
Adjust Exhaust Tip Forward From Under Bumper
Another thing to check is where the duals are connected to the muffler outlet pipe there is a notch to how far the pipe is inserted you should be able to feel for it or see it with your phone if one isn't inserted all the way you can also see it there and will have it stick out further Sent...- Tpearson515
- Post #6
- Forum: Exterior
-
Alright guys.. BILSTEINS post your pics!!!
Looks great man, recently got a 19 classic warlock coming from a lifted 15 that I had bils on.. any chance you have before and after measurements? Or just the current measurements? The rake on my 19 currently is about 3 inches which was a bit higher than my 15 so I was debating going with a rear...- Tpearson515
- Post #2,226
- Forum: Lifted
-
Tire help can't make up my mind.
I'll second this i had a set of the previous grabber at2 before they went to atx, got about 55k out of them, I ran 275 65 20, great in the snow/rain (Maine), and a decent looking tread, not to mention very little if any road noise at all on the turnpike. Sent from my SM-N975U using Tapatalk- Tpearson515
- Post #20
- Forum: Exterior
-
Installing cab clearance lights on my 1500
When I ran power to my mirrors to change them from turns to clearance lights I pulled the PCM up (which just un clips) and found the power out of my clearance light fuse cut into the wire (underneath) soldered and used heat shrink, I can't imagine 5 led clearance bulb lights pulling more than a...- Tpearson515
- Post #2
- Forum: Exterior
Staff online
-
G-Ride990Administrator
Members online
- Travis8352
- prowess9292
- smoothee
- bowhunterjae
- Lsujker
- Neilr5515
- AZ MARK
- CanuckRam1313
- jabartram
- EriikK
- Mb7640
- Musky Mike
- FJ Mike
- lkmiller
- Dontra
- Black-Wolf
- gt8684
- Choicebro
- RAMPO
- StateOfMind
- BenWade
- jimww333
- Motoman501
- G-Ride990
- Jamesg0418
- Matt Jackson
- Tulecreeper
- 2021cummins
- davidthomas97
- andres124501
- kaydubb77
- Javier Prado
- HarryS
- RebelDad
- bucnut
- tjfdesmo
- mrack
- rage32
- atom13