Search results
-
2018 3500 6.4l purge valve location?
It’s under the engine cover on the passenger side of the engine. The white clip was a PIA to get out- Gordo2212
- Post #4
- Forum: Heavy Duty
-
-
2018 3500 6.4l purge valve location?
So I got the check fuel cap message a week ago, then the CEL for it. I put in a new cap and cleared codes. Less than 100 miles later I get just the CEL with no check gas cap light. Codes are for gas cap, small evap leak and large evap leak (p0456). I'm going to change out the purge valve but...- Gordo2212
- Thread
- Replies: 3
- Forum: Heavy Duty
-
Revmax thermal bypass
Just did this today and I'll tell you what. It's a lot harder than the video's make it look. LOL The top screw was so freaking tight, what a PIA to get that loose, especially with how tight it is to get up there. Then the bottom line was bent in a way that didn't let the nut push back after it...- Gordo2212
- Post #11
- Forum: Dodge Ram Power Wagon
-
Revmax thermal bypass
Is there an install video you checked out before replacing?- Gordo2212
- Post #7
- Forum: Dodge Ram Power Wagon
-
Vibration when accelerating at low speed
There's a whole bunch of reasons that could happen. Bad cv axle, transmission shudder, tire balance is off, etc... I would have a shop troubleshoot the issue for you.- Gordo2212
- Post #2
- Forum: General Discussions
-
CarLinKit wireless apple play
Front of the unit says CPC200-U2W Plus -
Should I Add The OEM Trailer Braking Module And Get Alfa OBD, Or Go 3rd-Party?
The brake controller will not work unless you enable it with Alpha or have the dealer flash the code. The module is a giant pain in the ass to install FYI. The dry weight they tell you online doesn't account for propane, WDH or anything you put in the camper. Sounds like you're cutting it...- Gordo2212
- Post #2
- Forum: Towing & Hauling
-
-
Looking for OEM AUX Switch Panel. All I have is the Tow Switch and the Anti-Slip Switch.
They should sell it as a kit and you can install it yourself. Like chri5k said, hit up @AllMoparParts.com and Benny should be able to get you the part number for the kit for your truck. -
Power Folding Mirrors
You have to push them up by hand. The mirror goes from horizontal to vertical. The power fold means the entire assembly folds inwards towards the door. -
Limp mode - no codes
This happened to my 2018 3500 6.4l. Would go into limp mode with no codes while towing my camper. CE light eventually came on though. It was the valve body. Got that changed out under warranty and no problems since.- Gordo2212
- Post #7
- Forum: Engine & Performance
-
Help with break bleed?
Those are the procedures I followed except not doing a last manual bleed on the right side. I have more fluid so I'll do another manual bleed tomorrow I suppose to make sure all the air is out. Thanks for the info.- Gordo2212
- Post #3
- Forum: Heavy Duty
-
Help with break bleed?
Yesterday I switched out the HCU for ABS system on my 2018 3500 6.4l. I did the initial bleed then ran the ABS bleed in Alpha. I expected to have to open all 4 valves but it only did the passenger front and rear. I did it twice to make sure I didn't screw it up but started on front right then...- Gordo2212
- Thread
- Replies: 2
- Forum: Heavy Duty
-
CarLinKit wireless apple play
Purchased this last summer, original everything. Works great. Haven't used it as much as I thought I would. 60$ shipped. I have PayPal and Venmo. -
NHTSA finally opens ABS/HCU investigation
I had the ABS/EBS lights going on and off for a while. Found an HCU to replace and then it stopped. Hasn't happened in over a month. If someone needs it send me a PM and you can give me what I paid for it.- Gordo2212
- Post #23
- Forum: Heavy Duty
-
EBS/ABS lights coming on intermittently?
Sounds good. Is break fluid 04318080GD the right one for my truck? I'll need some of that as well. Also is there a shipping code for the holidays going on? Thanks for all your help!- Gordo2212
- Post #9
- Forum: Heavy Duty
-
EBS/ABS lights coming on intermittently?
Oh yeah that's just to bleed out the air after installing the new HCU. I thought you meant when taking out the HCU. You can do it with a scanner. I'm pretty sure Alphaobd can activate the ABS bleed.- Gordo2212
- Post #7
- Forum: Heavy Duty
-
EBS/ABS lights coming on intermittently?
Special tool to bleed the HCU? The few video's I've seen doesn't mention that. Looks like you unscrew the lines on the top and let the brake fluid drain down.- Gordo2212
- Post #5
- Forum: Heavy Duty
-
EBS/ABS lights coming on intermittently?
Do you all have the HCU in stock?- Gordo2212
- Post #4
- Forum: Heavy Duty
-
EBS/ABS lights coming on intermittently?
I have a 2018 3500 with 6.4l engine with about 49,000 miles on it. Randomly started getting the ABS/EBS lights coming on and off starting about a month ago. Doesn't seem to be a rhyme or reason, they will come on and off a few times and then go away. Some drives they don't come on at all, some...- Gordo2212
- Thread
- Replies: 29
- Forum: Heavy Duty
-
4th Gen parts
Sorry, haven't logged in for a while and just seeing this. I'll go check my garage to make sure I still have everything. Edit: I still have everything. -
Ram 1500 Classic Apple CarPlay
In my 2018 3500 the only port that works for carplay is the left one inside the jump seat (after upgrading the media hub). I think you can enable other ports to work as well with alpha though.- Gordo2212
- Post #16
- Forum: Audio & Electronics
-
