Search results

  1. bassheadhemi

    ARH Headers leaking

    So I had my ARH headers installed for over 2 years and recently noticed something that sounded like a small leak coming from front. Yesterday I got my transmission fluid changed and asked the guy to have a look/listen at it. It's tire season up here so he didn't have time to look at it for very...
  2. bassheadhemi

    RP filter issue?

    I keep seeing the larger Royal Purple 20-820 filter being recommended over the 10-48 one. Any issue with the 10-48? I just ordered 2x 20-820 on Amazon.ca (almost half the price of the 10-48), but still have one 10-48 in stock and want to make sure there's no problem with them. Sent from my...
  3. bassheadhemi

    Redline gear oil issue?

    Last weekend, I changed my diff and tcase fluid with Redline fluid. Since, the rear diff is making a humming noise (sound like tire noise). Truck have 3.92 with limited slip I've use the Red Line 75w140 (Not the NS one) I've check the level and it's fine Jacked up the rear and was able to...
  4. bassheadhemi

    Diff and transfer case (44-45) oil

    I have 2 questions. For the front diff, can I use the Redline 75w90 with modifier even if I don't have LSD? the 75w90ns is more expensive so wondering if it matter. For the transfer case since I have the 44-45 is there a better ATF4 that I should use? Sent from my SM-N950W using Tapatalk
  5. bassheadhemi

    Chambered vs straight-through muffler issue?

    A few weeks ago I decided to try the Flowmaster 50HD, coming from multiple (Magnaflow, Borla, Afe) straight-through mufflers the first thing I noticed is that it had more torque under 2500 rpm. I did a few WOT pull and it didn't felt as strong as before, but could have been in my head. Now...
  6. bassheadhemi

    Unequal length y-pipe

    Anyone running a custom equal length Y pipe? I've read that the unequal length will affect the exhaust pulse merging at the Y. It will affect the sound and also potentially performance if the pulses bounce back to the engine. I remember running my truck open headers after installing my ARH LT...
  7. bassheadhemi

    Magnaflow muffler freezing

    Ok so I swapped my 22" SI/SO Magnaflow for the the same muffler but in SI/DO config since I wanted to try the dual tails I had found. While taking the old muffler out I noticed that it weighted a lot more than the new one I got but didn't think much of it at time, but a few days later there was...
  8. bassheadhemi

    Rebel rear bumper on non rebel trim

    Looking to replace the rear bumper on my Tradesman for one that will work with the dual exhaust and I would go the Rebel one (68271595AA) since it doesn't need to be painted (powder coated), but wondering if it will work like the other 1500 bumpers
  9. bassheadhemi

    V6 efan mod issue

    idk if it has been discuss before, but while watching the latest BoostedMotorsports video it remembered me that I had the same issue he seem having with the upper hose rubbing against the efan. On mine I trimmed the plastic piece so it no longer rub, but it already made a small indentation in...
  10. bassheadhemi

    Tuner options

    Ok so my Diablo i2 took a dump and will need to be replaced. The cheaper option is to replace it with the Diablo i3 as they will offer me a discount since the device is broken, but out of warranty. The other option is the HP Tuner, but it's much more expensive (more than double than the i3)...
  11. bassheadhemi

    Cam option

    Starting to get funds aside for a cam to get a bit more power, but mostly for the sound. This is for street use only tbh I have no clue about cam, I understand what they do, but can't tell if that lift with this duration is good or not. when replacing the cam on those hemi what else should...
  12. bassheadhemi

    P26AB cel (3way coolant valve replacement)

    So my truck kept throwing me this P26AB for the last couples of months and it got to the point it was now everyday. Ordered the OEM part (52014892AC) some hose clamps and did the job in 15 minutes. I used the video below to guide me, but instead of removing the bracket, I simply unclipped the...
  13. bassheadhemi

    JET 180 Thermostat failing?

    I've installed the JET 10183 180deg Thermostat 2 years ago and ran without issue, but I noticed lately that when I start the truck in the morning to bring my daughter to school the truck will get up 212 before it open and when it's open it will not go below 195 (fan on or on the hwy). Before it...
  14. bassheadhemi

    Interesting video about aftermarket diff covers

    We don't have the result yet, but the theory is that when you change the cover you change the design lubricant capacity and this could cause more harm than good. Can't wait for part 2.
  15. bassheadhemi

    ARH Headers with high flow cats exhaust setups

    Ok guys what exhaust are you running after your catted ARH headers? I tried different setup and can't get what I want so I'm interested in knowing what you did and how you like it. I'm looking for a civilized cold start, deep sound and doesn't drone. The best I got so far is with a dumped 22"...
  16. bassheadhemi

    Borla pro xs (single exit)

    I decided to give the Borla a try based on multiples comments that it had a lower note. Having a single side exit I went with the 3" offset/offset (40353). This is a smaller muffler than what the dual exit guys are using (14" vs 19") but I hope the larger factory resonator of the single will...
  17. bassheadhemi

    Diablo tuner (and maybe other tuner) and iDatalink Maestro RR compatibility issue

    So I've upgrade my head unit and used the Maestro RR for integration with the truck. Everything was working flawlessly, but last night when I tried to change the tune of my truck it failed, the tuner was in recovery mode and couldn't get the truck back to stock. I called to Diablo this morning...
  18. bassheadhemi

    Brake

    I just want to know if it's normal for our truck to never get a hard brake pedal when you pump the brake (engine on)? Is this because of the ABS?
  19. bassheadhemi

    ARH Headers replacement bolts/nuts for the y pipe

    Looking for replacement hardware because mine are badly rusted after only one winter. Not sure if there's anything better in term of material to prevent the rust to form so quickly.
  20. bassheadhemi

    Exhaust leak (not manifold)

    Now that I've installed a quieter muffler, I noticed some noise from under the truck (only when cold). I've setup my shopvac in reverse, put the hose in the tailpipe (sealed) and then started to spray soapy water on every clamps, well they ALL leak... I guess having everything welded is the...
  21. bassheadhemi

    Used engine/Xcase/trans

    I've found a guy who's selling a complete power train (5.7 Hemi/44-44 Xcase/8speed) from a 2016 Sport with 11,000 miles for 1600$. should I grab it and how much do you think I can sell the xcase and transmission? The idea would be to build this block
  22. bassheadhemi

    Used tire

    I was shopping for some new BFG KO2 275/65r20, but found used 285/65r20 that are 1/3 of the price of a brand new set of 275. 2 are at 12/32 and the other 2 are at 13/32, so they still got some life left in them. Any gotcha with tire of this size when buying used? Also, from what I read so...
  23. bassheadhemi

    Magnaflow muffler missing a weld?

    I noticed that on my new muffler one side is not welded, at first I thought it was normal but now I don't think so since my previous magnaflow were all welded. Normal? Sent from my SM-N950W using Tapatalk
  24. bassheadhemi

    Confort and number of ply/sidewall height

    So my tires will need to be replaced before winter and I'm debating if I keep the stock size 275/60r20 (33") or go a inch taller with the 275/65r20(34"). My ko2 right now are 8 ply and a max psi of 65, but the 34 are 10 ply and have a max psi of 80. So will the ride be harsher with the 10 ply...
  25. bassheadhemi

    ARH Headers torque specs?

    I'll be installing my headers tomorrow morning and can't find the torque specs for any of the bolts... Anyone have an official document? My Remflex gasket says 20ft-lb so that's what I'll use, but for the band clamps and the bolts that attach the headers to the mid pipe I have no clue.

Latest posts

Members online

... and 6 more.
Total: 1,257 (members: 56, guests: 1,201)
Robots: 1,731

Forum statistics

Threads
195,606
Posts
2,872,466
Members
156,423
Latest member
BBernal

Share this page

Top