It's common in certain areas where I live and you're always worried about it. They are extremely fast and work as a team. If you have security cameras it only means you get to go back and watch how your converter was stolen. My buddy had his ripped off twice within a year. Got video both times...
If your truck didn't come with the power sliding rear window you most likely don't have the wiring. I have done a few including my truck and built my harness to use the factory switch. None of the trucks I have done had any of the wiring.. There is no setting for this in the Alfa tool. The...
This option was not available in 2014. You will have no place to enable it in your BCM. The only way to do this with a 2014 is to enable the cargo cam option. This will bring up the "Cargo Cam" icon in your Apps screen. You would push on cargo cam and then it gives you the option to press the...
There are 3 wires for the factory heated seat pads. Heat sense heat return and heat control. I'm not sure if you would be able to regulate the heating pads with any type of aftermarket switches or setup. The seat vents have two speeds in the factory setup but you could wire them up to just turn...
There would be a possibility but you would need to pull the driver's side back seat out to check and see if it has the extra connector for the RF hub. If that wiring was present then you could work back from there to check for the rear door antenna wiring and the door handle wiring in the front...
The heated steering wheel will not work unless it's controlled by the factory heated seat module. If you decide to go aftermarket with your heated seats that's 100% fine but you are going to give up several features. The switch panel under the radio is connected to the CAN system in the truck...
Replacing the 02 sensor definitely isn't what I would start with if you have the P300 code which is multiple random misfire and the P307 code which is a misfire on cylinder 7. I would do a compression test to make sure your not having the dreaded cam and lifter issue which in your case I think...
As stated they will not work. It is extremely simple to pull your old switch without the +/- and switch them out so you don't have buttons in your wheel that don't work but that's up to you.
Sent from my SM-G981U1 using Tapatalk
This cannot be changed. It's encoded into the radio. I guess a software engineer could figure it out so I will rephrase my answer by saying it may or may not be something that could be done by a extremely knowledgeable software engineer but definitely not by a person with average understanding...
You 100% don't have the wiring for heated/vented seats or power seats. You can purchase a conversion harness at M2mods in the vendor section of the forum. It is plug and play and installs exactly the same as the factory harness. You would also need to purchase the Alfa tool to enable the codes...
You can purchase an RA3 VP3 NA non nav radio on eBay for $300 to $350 pretty easily or the RA4 VP4 NA factory Nav radio for around $350 to $400. It's extremely simple to replace and there is NO special programming required. The radio the dealer installs is almost guaranteed to be refurbished so...
Unfortunately your heated steering wheel is controlled by the Heated Seat Module mounted to the bottom of the factory heated seat. The truck will not communicate with the steering wheel without it.
Sent from my SM-G981U1 using Tapatalk
Yes, the heated steering wheel takes a separate harness than the regular steering wheel. There should be no connectors left unused for the heated steering wheel. As far as the heated/vented seats not showing up on the radio I don't have any answers for that as long as you have all the options...
Check your third brake light. This will cause a tail light out message. There is a good chance that's what it is.
Sent from my SM-G981U1 using Tapatalk
Contact Mike @M2mods in the vendor section of the forum. He builds the custom harness for this conversion. It looks and works exactly as factory. You will have full power options, heat and vent if the seats are capable plus the heated steering g wheel. You can also have him include the wiring...
These seats have completely different wiring and modules than your 2016. The 09 to 12 seats are completely different than the 13 to 18 and Classic. There is no conversion harness to make them work. These seats will not communicate with your truck's CAN system. You may be able to completely...
If your new seats are from a 13 to 18 or Classic they should be plug and play if your 16 already had the heated/vented seats. The 09 to 12 trucks used a completely different setup. What year are your new seats out of?
Sent from my SM-G981U1 using Tapatalk
I agree, but unfortunately you're going to pay a dealer or someone else around $100 Min to check for DTC codes that may or may not be present and this is money you can't get back. There is no way to diagnose the problem other than checking the wiring and connectors without the correct scan tool...
A regular scanner cannot check for DTC (Diagnostic Trouble Codes). They can only check for OBD (On Board Diagnostic) codes. You would need the Alfa tool or similar tool to the dealer. We are very familiar with this because we actually added the Dual Zone ATC to our trucks and had this exact...
Since your truck is a Longhorn it has the Dual Zone ATC as standard equipment. There is a Humidity Sensor on the 14 and up 1500 trucks located to the right side of the rear view mirror covered by a small black cover that attaches to the windshield. This pops off to access the sensor that...
It's definitely nice to see a few guys taking the plunge and taking on this mod. As I've said several times it's really not as hard as one might think so it scares some people away. The Dual Zone ATC is definitely a nice feature to have. It's going on about two years since I upgraded mine and it...
Yes, if the dealer makes a flash(update)to the BCM the trailer brake code will need to be reinstalled. In many cases they actually update other modules in the truck and not the BCM so it won't bother you at all in that case. The Alfa Tool will do much more than just enable the trailer brake. It...
No, there is no special programming required or codes needed. All you will need is the 4 digit radio anti theft unlock code. You will also need a conversion harness if you want to do the full upgrade with the 8.4 bezel. Contact Mike @M2mods in the vendor section of the forum for anything you may...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.