Search results
-
Ported Manifold
I’m still hard pressed to believe a ported manifold provides that much power. Personally, I’m waiting to do a 6.4 intake manifold swap and ported TB. I’m hoping the tracks open up soon enough for me to get some times before I swap, so I can provide some FBO results with and without the 6.4 IM...- LuisJr
- Post #12
- Forum: Engine & Performance
-
Not Going Back Sale, Everything Must Go!
Is the Carven still available? I’m located in Ventura County, north of you. Luis -
No one ever post about drag racing in the performance section....lol
Hahah yeah. Like I said before you're a wealth of knowledge. This is Luis Schmitzberger, Jr from all the Ram pages! Yeah I really hope to get the geometry dialed in before she gets a big power increase.- LuisJr
- Post #124
- Forum: Engine & Performance
-
No one ever post about drag racing in the performance section....lol
Rick? Lol- LuisJr
- Post #119
- Forum: Engine & Performance
-
No one ever post about drag racing in the performance section....lol
@Wild one That's what I had in mind lol Ive slowly started to push it off though, seeing as a few 8spd RCSB guys are running without the brackets and still getting into the mid 1.60s with bad geometry. I think the next two big mods will be a converter and driveshaft done locally. The old...- LuisJr
- Post #117
- Forum: Engine & Performance
-
No one ever post about drag racing in the performance section....lol
@Stelios Yeah it sucks I wish Illicit was still around with their brackets. I heard much better results. Hopefully this will get resolved soon with Matt helping out. More than likely I'll probably take that money and invest it right back to him for more parts. Probably as a fat payment...- LuisJr
- Post #115
- Forum: Engine & Performance
-
No one ever post about drag racing in the performance section....lol
Followed directions exact and still had issues with bottoming out. Actually worse than before. Contacted them to explain the issue and had a vague response. Sent them a video and pictures of the upper control arm mount hitting the frame. Per their instructions the upper mounts have to be backed...- LuisJr
- Post #112
- Forum: Engine & Performance
-
No one ever post about drag racing in the performance section....lol
Hell no!!! Just checked Fontana now on DragTracker and it says 87* and DA of 3358ft... Barf lol What does everyone use for DA apps for the strip? Luis- LuisJr
- Post #110
- Forum: Engine & Performance
-
No one ever post about drag racing in the performance section....lol
I might be wrong, but I'm pretty sure Nick (Incredible Hemi) runs the 11.5 on the 17x7 wheels. Check out the FB pages, TunedRams, High Performance Rams etc. Tons of info there. But since I'm in the thread I might as well update my current set up. Hoping to hit Fontana on Sunday for Street Day...- LuisJr
- Post #108
- Forum: Engine & Performance
-
belltech 2/4 1/2 lower in rear ?
I used a crow foot to hold it. But I think others use a stubby or chopped down wrench. -
belltech 2/4 1/2 lower in rear ?
There is where I'm at. I cut off my bumpstop bucket per Inez Hotrods instructions and I have done nothing but slam super hard on the frame just looking at a bump. It's so bad, I'm glad my dad had a set if 2" rear drop springs. I'm currently on those with 2.5 coils cut out but now my rear is up... -
Bottoming out a lot!
Ah ok. Well I hope you get it resolved. I have the 2" drop rears on and cut two coils off them. Still too high for my liking lol But on a good note, it rides night and day better. I think I need at least one more coil to get me to 1" rake front to rear with a full tank of gas and work gear in bed. -
Bottoming out a lot!
You may just be too low. I'm having the same issues with bottoming out now that I added the Inez no cut brackets. Now that the axles is corrected, the upper control arm mounts are hitting the frame. I measured from hub center to fender and came up with 18.5" in the rear. Stock measurement was... -
Core 4x4 Panhard Bar
Sorry for not getting back to you Nick!! Been slammed with work. But I'll be reaching out soon enough to take you up on that quote you sent. Thanks again, Luis -
Core 4x4 Panhard Bar
I can't believe how beefy the Core control arms are. The lowers are monsters lol Can't wait to grab the panhard and uppers Luis -
Core 4x4 Panhard Bar
Looks great with the Mag-Hytec cover!!! I've thought about getting one one before I install the LSD. Any issues with leaking? -
Viking Warrior Shocks
I started out at 3c5r, sticking to the manual. Then bumped it up to 5c7r. I'm in the middle of doing the Inez "no cut" brackets. Once I finish the install I'll see how the ride has improved then go back to adjusting and bump them up again to 8c8r front and read and see where that gets me. Luis -
DO I need new shocks?
Hows the adjustment on the Spohn, any cracking at the welds. Other two things that come to mind is wheel bearing or dragging caliper. -
-
DO I need new shocks?
Maybe control arm relocation brackets are the next step. I'm going to do mine possibly tonight after work. The control arm angles look super terrible lol I'll report back when I get it done. Luis -
Big hats off to Graygoose and JBA header questions
Those are super cool! Might have to consider those when I do headers.- LuisJr
- Post #5
- Forum: Engine & Performance
-
-
Core 4x4 Panhard Bar
My only concern is now that I have the relocation brackets on the way, how would it affect them. Only one way to find out. I'll get all the other stuff installed then if I'm still bothered by the stance, I'll order the 2" springs off Amazon to test with. If I go that route, I'm pretty sure I'll... -
Core 4x4 Panhard Bar
I'm pretty sure its sitting on the rear bump stops. When I was jacking up the rear it looked like it went straight to the bump stops lol I'll get some pics when I get all the other parts in from Moe's. Part of me knows it is going to look sick on a racestar drag pack, the other part of me...
Staff online
-
rule18Admin
Members online
- smoothee
- Jasfish18
- Cool_Hand_Luke
- amadhi89
- HemiSue
- Warlock656
- Dinky
- aszumilo
- Curmudgeon
- barr0208
- Jeepwalker
- rule18
- RetiredSERE
- Suma Performance
- DanielPG
- AZ MARK
- T951
- Canacain
- ClarkR
- bob49
- RamHackerSK
- Daw14
- TRK_GANG74
- Team Horner
- Slinge
- Neilr5515
- dlevy504
- blkbrd666
- Justin33
- Udy2554
- VikeFan
- StateOfMind
- FLATLINER
- Marshall
- Buddy
- Corvette427
- ProsperRam
- nlambert182
- RebelDad
- Spankie
- Morka777