Search results

  1. Mcginnis

    GTR ultra 2 LED headlights

    Just wondering if anyone is running these in their projector headlights. Heard they’re great then I keep seeing projectors need to run HID I have some Alpharex g2 pros with a 55w HID kit that over a year has appeared to have grown dim. Not near as bright as I remember. Was thinking of just...
  2. Mcginnis

    Upkeep question

    Just wondering if there’s a thread on here for the 4th gen hemi upkeep I’ve just rolled over 50k miles and just wanting to get an idea of what I need to plan on doing in the future. Like spark plugs and wires or transmission fluid and filter change timing chain or tensioner rear diff service...
  3. Mcginnis

    Lifted with rear control arm relocation brackets

    Anyone lifted their 4th gen after lowering it and using the IHC rear relocation brackets?? Wondering how bad the rear axle would be shifted
  4. Mcginnis

    Belltech spring numbers

    Can someone give me the numbers off of a front drop spring for a single cab and the front drop spring of a crew cab. Not the part number 4762/4763 but the long number that is printed on the actual springs . I believe my crew cab has single cab springs in the front. Any help is greatly...
  5. Mcginnis

    AlphaRex pro G2 help……

    Having a problem with my passenger side light after install. There is no cutoff line and just a big hot spot. Wondering if I can fix it myself or no. Installed hids also. Posted 3 pics of both lights on, passengeronly and driver only. You can see in the passenger only there is no cutoff and I...
  6. Mcginnis

    Rear springs are cut!!

    I pulled the belltech springs out yesterday and cut a coil off the top. Put back in and drove around a bit. Looks like it only dropped 1/2in instead of 1 full inch. Just wondering if this is common or does it just depend?? I’ve been reading everything and thought 1 coil was 1 inch.
  7. Mcginnis

    Lowered measurements

    Hello all I’ve got a 2017 sport Crew cab that’s lowered on a belltech 2/4. I’ve got 285/45r22 tires on it. I was just wondering what everyone else’s measurements are with 2/4 or 3/5 drops. Im pretty sure mine is sitting lower than 2/4. (From level ground to middle of fender) My measurements...
  8. Mcginnis

    Inez Relocation brackets

    Ok. I bought the relocation brackets and waiting on them to come in. My question is I only have an angle grinder and was wanting to keep the rear end under the truck while I do it. Can I cut off the mounts with just an angle grinder or is a plasma cutter the only way to do it. It looks fairly...
  9. Mcginnis

    Any other rear control arm brackets

    Just wondering if there is any other rear control arms relocation brackets besides the Inez cut brackets. I saw illicit had some no cut brackets but I can’t find any for sale and Inez discontinued their no cut brackets.
  10. Mcginnis

    Shocks for inez drop

    I know it's been covered but I am wondering what options are for the front. I have a 2014 ram rcsb lowered with the inez 4/6. Thinking of swapping the rear shocks for the KYB kg54308. wondering what front shocks everyone has for the inez drops? I know the viking shocks are the best but a...
  11. Mcginnis

    Headers.....no tune

    I've got JBA long tube headers coming with a catless ypipe My question is it may be a bit till I get a tune Wondering if I can run them without a tune or if it will be to lean to run a while.
  12. Mcginnis

    Tire size for stockers with inez4/6 drop

    I'm about to order the inez 4/6 drop for my 2014 ram single cab and am looking at some 285/50r20 for my stock 20s. Just wondering if this size will be ok or if I need a smaller tire thanks.
  13. Mcginnis

    Diesel "death wobble"???

    Hello all. I am debating on getting a 4th gen Cummins. I've wanted one for a while. I've seen a lot of videos showing this death wobble and read a couple of posts on forums about it. Kind of scares me. Should this make me not buy one or is it a rare deal? Just wondering before I pull the...
  14. Mcginnis

    Best Jack for lifted truck

    Hello all. I recently had the maxtrac 7" lift thrown on my truck with the 3" body. The guy that did it forgot to put the rear spacers in. I was wondering what would be the best Jack to use to lift it up and put those in. I lowered my old 2012 Ram no problem but with a big lift I can't use my...
  15. Mcginnis

    Time for new tires. Need help!!!

    I'm running 35x12.50r20 on my truck now. They are the Federal couragia. They've been great tires my only complaint is they are pretty loud as they wear down. I'm looking at the fuel gripper mt for my next ones or the Cooper discoverer stt. I'm leaning toward the fuels because I love the tread...
  16. Mcginnis

    Car wash (lifted truck) friendly DFW area

    About to have a 10" lift put on my Ram 1500. I know most drive thru car wash is 7'. Just wondering if there are any drive thru car washes that would accommodate my truck with a 10" lift around Dallas. Preferably east of Dallas. Thanks
  17. Mcginnis

    37s and gears??

    Hello again. I have a 2013 Ram CC express 2wd. I'm looking at getting 37s after my lift is put on. I'm thinking my truck has the 3.55 gears. I'm just wondering if this would be OK or do I need to swap to 4.10s. Didn't really want to do a gear swap so I was wondering if the 3.55s would be to...
  18. Mcginnis

    Service TPMS????

    My light came on around 2000 miles ago. I'm getting tired of seeing it. It says service TPMS but the sensors are working and reading each tires psi. What is the deal with it. May be silly but could it be a deal to tell me to rotate my tires? Don't know any help would be great. Don't really...
  19. Mcginnis

    22x14 wheels?????

    I'm in the market for some new wheels. I'm putting on my lift in a couple of weeks and wanting to know if 22x14s will put to much strain on your hubs or studs?? Can't find much to answer my question in the search. I'm about to have about 11.5" lift on and was going to run the 22x14 with...
  20. Mcginnis

    Exhaust????

    Just wondering if you could run a 4 inch exhaust straight single pipe with 6in. tip on a Ram 1500 like a diesel. I saw a guy on Instagram had his 1500 with 3in straight pipe from cats back with a 6in tip. Sounds like a diesel at idle. Just wondering if 4in is to much.
  21. Mcginnis

    2013 Ram 1500 tow mirrors

    I've found a bunch of tow mirrors with the temp hookup for my truck but my question is do they make them without the turn signals and puddle lights. Everyone I find that electric and heated also has the lights with it. Any help will be great to point me in the right direction
  22. Mcginnis

    2" rear spacer

    Do they make a 2" rear coil spring spacer. I found one u put on the bottom of the rear spring but you have to drill and tap to put it on there and put bolt in. Just wondering if anyone knows of one.
  23. Mcginnis

    Moto metal 962 or fuel maverick

    About to buy some 20x12 wheels for my 1500. Wondering which one would be better. Wanting to get opinions from y'all. I'm going with the black style also. Thanks
  24. Mcginnis

    Wanting to see 7" Maxtrac

    Hello all. As of today I have a 2013 2wd crew cab 1500 that has the 5in performance accessories lift on it with 35s on the moto metal 961. Well I want it higher so I'm looking into the 7in maxtrac lift with my 3in body so I can have a total of 10in. Probably gonna throw some of the moto metal...
  25. Mcginnis

    20x12 -44 offset on 5" lift?????

    Hello everyone looking for an answer I'm interested in putting the moto metal 20x12 wheels on my 2013 ram 2wd that's lifted 5" I already have 35x12.5 tires running on the stock chrome clads I'm going to use those same tires and was wondering if ill have fitment issues. I also have 1/4" wheel...

Latest posts

Staff online

Members online

... and 20 more.
Total: 1,581 (members: 70, guests: 1,511)
Robots: 1,660

Forum statistics

Threads
195,606
Posts
2,872,455
Members
156,422
Latest member
keva

Share this page

Top