Search results

  1. K

    Power steering cooler location

    Good morning, I am looking to see if anyone can answer the question of where the power steering cooler is located on the 1996 ram 2500. Is it in to rad? is it in the same spot as it is on the 1500? I'm going to be heading out to buy new steering components soon. And if it's in the rad, I will...
  2. K

    Fuel injector retaining wire and transmission question

    I have access to a hydraulic press, but I'll most likely leave that section for the pros. I'll have a look around again for the service manual, I had it for a while but then got a new laptop. I live in Red Deer Alberta Canada. So a quick drive would be a little long in the tooth lol.
  3. K

    Fuel injector retaining wire and transmission question

    I don't think the transmission was overly well cared for in the past. I'd like to do the work, but my lack of skill may end up costing me more than what I am willing to have go wrong. A lot of the shops where I live begrudgingly will work on vehicles with parts supplied. And none will allow for...
  4. K

    Fuel injector retaining wire and transmission question

    I'm not really sure, as at the moment it depends on the cost. I know that I will be doing some towing through the mountains, as well as trying to improve on my 4wheel skills. I wouldn't mind having it up to where it would be able to handle a 20% increase in HP and torque. And not turn into a...
  5. K

    Fuel injector retaining wire and transmission question

    Would you happen to have the link to the part in Amazon? For the rebuild kit would anyone have a suggestion as to what kit and stall converter?
  6. K

    Fuel injector retaining wire and transmission question

    Hello, I had taken my truck into the dealership to have them find an issue that I couldn't figure out. While they were working on it, they had noticed the wire clip was missing on all the injectors. Would someone happen to have a photo/part number or knowledge of where to get replacements? Or...
  7. K

    Aaaand again....

    Ok, so here's the scoop. I have a 1996 2500 with the 360 v8. With replacing the TPS, Oil sender, Crank sensor, plugs, wires. And now it won't stay running unless I am holding down the gas pedal to keep the rpms up. Could there be an issue with the computer? I can hear the fuel pump, and when...
  8. K

    Running issues

    Good afternoon, A while ago I posted about not being able to keep the truck running unless I had my foot on the gas. Still have that problem, posted my findings but no other replies to help me with this issue. I hooked up a fuel pressure tester and I have 40 PSI KOEO, when I start it and have...
  9. K

    Running issues

    Good afternoon, Late last year I had posted about not being able to keep the engine in my truck running unless I had the gas pedal to the floor. I can't get logged in on my computer to update the post. Over the last weekend I had the chance to try a few of the suggestions in that post. But no...
  10. K

    Engine confusion

    The engine still has the same injectors that came with it. They were just installed with new o rings. The engine ran fine from the video that I was shown prior to purchase. It's unknown to me on if they were changed out for bigger or not though. I'll get a pressure tester tomorrow and have a go...
  11. K

    Engine confusion

    Good afternoon folks, After using the search, mr google and the service book. I still can't figure out what's going on with the truck. I have a 1996 dodge ram 2500 with the 360 gas engine. After having the compression test done, and it reading 80 on all but 2 cylinders. I had changed the...
  12. K

    Measurements please!!

    Would anyone happen to know off hand what length of Nerf bars a guy would need? I have been looking around for a set, but all I can see are one with double foot pads on them. My Dodge is a 96 2 door. And right now I don't have access to the truck to measure what I'd need. Thanks Sent from my...
  13. K

    Manual seats

    This is the latch that I was referring to. Sent from my E6653 using Tapatalk
  14. K

    Manual seats

    Good afternoon community!! I have a few questions as far as the manual seats are concerned. I have a 1996 ram 2500, and it doesn't have the spare door. My seats manually slide forward amd the back of the seat folds forward. The questions I have are, is it possible to repair the latch for the...
  15. K

    Coolant boiling out

    I've had it where the thermostat failed half closed, as well as my water pump starting to fail. That may be something to check out. Sent from my E6653 using Tapatalk
  16. K

    Quick question on engine mod

    One more quick question. Would I have to "modify" the valve covers for the 1.7? I have read that some have needed to mash the baffles Sent from my E6653 using Tapatalk
  17. K

    Quick question on engine mod

    Nice! Thanks for the help. Now to get the heads checked and set up Sent from my E6653 using Tapatalk
  18. K

    Quick question on engine mod

    Good evening, Well after doing a crap ton of reading on mr google and here, my questions still hadn't been answered. I have recently become the new owner of a set of magnum heads from a 2001 5.9. And for the best possible price yet too.... The questions are will they fit on a 1996 magnum 5.9...
  19. K

    NightMares 01 Sport Build

    Page book marked, took a while but the whole thread has been read! Nice build up again and I hope your business goes well. Sent from my E6653 using Tapatalk
  20. K

    Freeze plug looks bad

    I haven't done mine yet, but I know that one a 289 that I'm helping with we had to drain the coolant and pull the coolant plugs from the back of the block. After that it was removal of the starter and pop them out. Clean the seat really well and seat them back in. Sent from my E6653 using Tapatalk
  21. K

    Where you from?

    Red Deer Alberta Canada Sent from my E6653 using Tapatalk
  22. K

    NightMares 01 Sport Build

    I like the box at the front. Nice and compact, doesn't take up the room that the big chrome tool boxes do. Plus still get the tonneau cover Sent from my E6653 using Tapatalk
  23. K

    Tires or traction control

    For when I get into those kinds of traction issues and have to put in the 4x4, I also put the traction control off. And don't usually have issues. The company I used to work for only runs duratracs in the summer and are great tires. Also come in load range E. Personally, the duratracs and the...
  24. K

    5.9 crank no start issue

    ECM fixed and now waiting on recall harness and dealership programming. Can't find a SCT anywhere near me, or even for my truck haha. Closest I came was for a 98, and the guy at the shop said it wouldn't work. Sent from my E6653 using Tapatalk
  25. K

    What did you do to/with your second gen today?

    Well, I finally got the beast running today. Installed my replacement pcm. Now all I have to is find a SCT programmer. Which is proving to be far harder than I had thought it was going to be. And the superchips programmer is just as hard to find around my area. If I had a diesel then there'd be...

Latest posts

Members online

Total: 762 (members: 30, guests: 732)
Robots: 1,389

Forum statistics

Threads
195,600
Posts
2,872,388
Members
156,412
Latest member
kdb777

Share this page

Top