Search results

  1. dmills0130

    Lifted 4th Gen Pics - Show Em Off!

    I'm running them in a 37x12.5x18 and I am not impressed as far as on road performance goes. All 4 of mine are out of round. I've contacted federal to see what can be done to rectify the situation. Sent from my SM-N920V using Tapatalk
  2. dmills0130

    turns over wont start

    If I remember right, those are brass seals. An o ring will not seal. Sent from my SM-N920V using Tapatalk
  3. dmills0130

    Lifted 4th Gen Pics - Show Em Off!

    Zone 6" 37's on 18x10 962's Sent from my SM-N920V using Tapatalk
  4. dmills0130

    turns over wont start

    Crack a few injector lines open and spin it over until fuel sprays out. Tighten them back and she should fire up. It may run rough for a minute or so. Sent from my SM-N920V using Tapatalk
  5. dmills0130

    Oil Catch Can Dump photos

    I am at roughly 55k miles. I do a fair amount of driving mixed and some 1500+ mile trips every few months. I am going to be installing a catch can after reading this. Question is, is there a safe method to clean the intake track before hand without removing intake and heads? Sent from my...
  6. dmills0130

    Warranty issues

    I'm working with FCA now. I've also placed a call to the owner of the dealership who had been very helpful in the past. Time will tell. Sent from my SM-N920V using Tapatalk
  7. dmills0130

    Warranty issues

    We only have 2 dealerships in town, one is a Chevy dealership, the other sells Ford and Chrysler products, I'm not sure if that has anything to do with it. Sent from my SM-N920V using Tapatalk
  8. dmills0130

    Warranty issues

    Yeah, I just priced a set of 5100 on amazon at less than 250 shipped. I plan on a 6" lift in the not too distant future so I will be able to adjust back down as needed to keep it level. Sent from my SM-N920V using Tapatalk
  9. dmills0130

    Warranty issues

    I bought it from the dealership when I purchased the truck as it was used with about 13k on the clock. That's what they offered me. I'm currently waiting a reply from FCA to see if there is anything they can do. Dealership quoted me ~450 for a strut installed plus an alignment. Sent from my...
  10. dmills0130

    Warranty issues

    Anybody have issues with Zurich extended warranty? I've found that my third brake light that shorted out from water damage isn't covered because it was due to a faulty seal. Also that my left front strut isn't covered due to it being a seal leaking vs the body. What's the damn point of paying...
  11. dmills0130

    Oil temps

    I'm normally around 206. Highest I've seen was 221 pulling my little truck through the hills of TN and KY Sent from my SM-N920V using Tapatalk
  12. dmills0130

    Knocking in bottom end

    Precisely. I typically avoid dealerships because of the hassle Sent from my SM-N920V using Tapatalk
  13. dmills0130

    Knocking in bottom end

    I think the argument will be the labor behind the broken bolts, because it's not the manifold that is broken. Time will tell and I'll report accordingly. Sent from my SM-N920V using Tapatalk
  14. dmills0130

    Knocking in bottom end

    No, I pretty sure I read that in mine, but now I may have been confused. It's going in in the morning for water leaking into my cab and strut that is leaking, so I'll bring it to their attention. Sent from my SM-N920V using Tapatalk
  15. dmills0130

    Knocking in bottom end

    Mine is a 13 and it happened to me while I was in Chicago on vacation in January. Sent from my SM-N920V using Tapatalk
  16. dmills0130

    Knocking in bottom end

    The warranty explicitly states that it does not cover broken bolts which is what caused mine. The factory manifolds are giant heat sinks with no material to dissipate heat to so they expand like hell and break the bolts off. Sent from my SM-N920V using Tapatalk
  17. dmills0130

    Knocking in bottom end

    Are you sure it's a knock and not a busted manifold or bolts causing an exhaust leak? I have an exhaust leak on the drivers manifold but it goes away after its warmed up. Not covered under warranty so I am waiting on some headers to repair it. Sent from my SM-N920V using Tapatalk
  18. dmills0130

    Center Console Swap

    Just curious, has anybody done this swap with the column mounted shifter? My OCD won't let me have the knob on the bezel. Sent from my SM-N920V using Tapatalk
  19. dmills0130

    Sway Bar Disconnects

    F that noise... I'll gladly take a wrench to them when need be. Sent from my SM-N920V using Tapatalk
  20. dmills0130

    Sway Bar Disconnects

    Does the power wagon not have the electronic sway bar disconnect? Would it be feasible to pull the system from one of those truck and adapt it over? Sent from my SM-N920V using Tapatalk

Latest posts

Staff online

Members online

Total: 1,224 (members: 46, guests: 1,178)
Robots: 1,796

Forum statistics

Threads
195,659
Posts
2,873,029
Members
156,510
Latest member
crxpd

Share this page

Top