Search results

  1. Tpearson515

    More lift for a Warlock

    Here is my 19 classic warlock with a 2 inch front kit 1 inch rear spacer and 1.5 inch body lift, On 35 12.5 20's, This is my second 4th gen ram I've done this to and very happy if you are on a budget, I also upgraded UCAs for peace of mind the stock ones worried me because there was separation...
  2. Tpearson515

    2019 classic warlock 1.5 body lift / level with oem tow hooks

    Hey j-b for some reason I can't send a pm with a picture, basically here is how I cut my bracket kept notching it down until it fit then re used hardware with blue loctite, I dry fit everything first it may be different on yours, hope this helps!
  3. Tpearson515

    2019 classic warlock 1.5 body lift / level with oem tow hooks

    Hey , looks great on 35s!, I think I have pictures I took, I always thought doing the body lift I wouldn't be able to use the tow hooks. After I got done with my install I tried to re install them and the hooks still lined up through the front holes, I took my original hardware slotted out the...
  4. Tpearson515

    2019 classic warlock 1.5 body lift / level with oem tow hooks

  5. Tpearson515

    2019 classic warlock 1.5 body lift / level with oem tow hooks

    Hey, this is my second body lift on a 4th gen, both times took me around 4-5 hours to install, I did check all my harnesses everything looked great,
  6. Tpearson515

    2019 classic warlock 1.5 body lift / level with oem tow hooks

    Just wanted to post here for anyone interested, I had been going back and forth on how I wanted to lift this truck up a little, long story short 2019 classic crew cab warlock Installed 2 inch top strut spacer, 1 inch rear spacer, 1.5 inch zone body lift d9150. My current from fender to ground...
  7. Tpearson515

    Zone body lift instructions. Just ordered a kit

    Hey Man, hope all is well! I remembered you had recently installed your body lift, I did one on a 2015 about 4 years ago now, I now have a 2019 classic warlock I'm putting one on, just did the level 2 weeks ago, and just orders the body lift! The only thing I can't quite remember is the front...
  8. Tpearson515

    4 “ ready lift on the 19 Warlock!

    Your truck looks great, do you have any pictures of the CV angles or the sway bar drop bracket? Without the drop bracket in this kit will the sway bars rub? Sent from my SM-N975U using Tapatalk
  9. Tpearson515

    4 “ ready lift on the 19 Warlock!

    I'm thinking of going with this ready lift route, my question is if I already have the rear suspension lift parts from another truck are you guys aware if any kits that include the ucas sway bar drop brackets and front spacers? I tried to contact ready lift to individually purchase the pieces...
  10. Tpearson515

    Under the rear wheel well liner

    Thank you that does help and yeah it will be in the way, appreciate the help though! Sent from my SM-N975U using Tapatalk
  11. Tpearson515

    Under the rear wheel well liner

    Does anyone know if you can reach the bottom side of the bed rail if you remove the rear wheel well liner, I have a small dent close to the top of the fender was just curious if anyone knew before I pull it off to check next week Thanks! Sent from my SM-N975U using Tapatalk
  12. Tpearson515

    Adjust Exhaust Tip Forward From Under Bumper

    Another thing to check is where the duals are connected to the muffler outlet pipe there is a notch to how far the pipe is inserted you should be able to feel for it or see it with your phone if one isn't inserted all the way you can also see it there and will have it stick out further Sent...
  13. Tpearson515

    Alright guys.. BILSTEINS post your pics!!!

    Looks great man, recently got a 19 classic warlock coming from a lifted 15 that I had bils on.. any chance you have before and after measurements? Or just the current measurements? The rake on my 19 currently is about 3 inches which was a bit higher than my 15 so I was debating going with a rear...
  14. Tpearson515

    Tire help can't make up my mind.

    I'll second this i had a set of the previous grabber at2 before they went to atx, got about 55k out of them, I ran 275 65 20, great in the snow/rain (Maine), and a decent looking tread, not to mention very little if any road noise at all on the turnpike. Sent from my SM-N975U using Tapatalk
  15. Tpearson515

    Installing cab clearance lights on my 1500

    When I ran power to my mirrors to change them from turns to clearance lights I pulled the PCM up (which just un clips) and found the power out of my clearance light fuse cut into the wire (underneath) soldered and used heat shrink, I can't imagine 5 led clearance bulb lights pulling more than a...
  16. Tpearson515

    Factory Flares Falling Off

    Absolutely agree with what Bowers said, when I re did mine, picked up some 3m tape from napa, used a heat gun to pull the remaining tape from the flares off , cleaning/prep is the most important thing then when I re-installed something I did that seemed to help I had a 6ft 2x6 that I rested up...
  17. Tpearson515

    1.5 body lift with OEM flares install question

    Ok thanks, my 15 was a little different in the front bumper I had to remove the headlights when i pulled it, this is a classic warlock I wasn't sure if that piece below the headlight had to come off as well, actually just watched a video of a guy removing his front bumper on a rebel which looks...
  18. Tpearson515

    Classic warlock/rebel 1.5 body lift question

    Ia there anyone here that has done this? I have a 2019 classic warlock and wanted to make sure that the zone 1.5 body lift 4x4 would work with this? Any pictures would be great!, mainly wondering about the front and how it will look without tow hooks, the kit number is ZOND9150 i installed this...
  19. Tpearson515

    1.5 body lift with OEM flares install question

    Hey guys, was just curious I installed a 1.5 body lift on my 2015 express that did not come with flares, I ended up installing flares after the lift. My question is I now have a 2019 classic with OEM flares, to anyone that has oem flares and installed their lift , did you need to remove your...
  20. Tpearson515

    Body Lift

    Something to keep in mind with the warlock as well youll have to remove or create new brackets for your front tow hooks, I had a 2015 express i put a bl on. I now have a 19 classic warlock only thing thst may be different is the front bumper but ill have to crawl under and look. Sent from my...
  21. Tpearson515

    No more rubbing

    Looks great, what brand did you go with? Sent from my SM-N975U using Tapatalk
  22. Tpearson515

    tire balance beads

    When I purchased my 33x12.5 20 mts the shop talked me into balancing beads, truck would shake like crazy,bafter 4 visits of trying different amounts of beads I had them take them all out and just use weights to balance, not sure if it was a problem with the shop knowing what they were doing or...
  23. Tpearson515

    Thick Tire on Narrow rim

    I ran 33x12.5 on stock 20x8 rims with no issue at all, I did run lower tire pressure than recommended just to be safe from uneven wear in the middle of the tire Sent from my SM-N975U using Tapatalk
  24. Tpearson515

    New Jack for lifted 1500

    I kept a couple of cut 2x4's under my rear bench seat :) Sent from my SM-N975U using Tapatalk
  25. Tpearson515

    Zone body lift instructions. Just ordered a kit

    Looks great man! Sent from my SM-N975U using Tapatalk

Latest posts

Staff online

Members online

... and 13 more.
Total: 1,347 (members: 63, guests: 1,284)
Robots: 2,089

Forum statistics

Threads
195,611
Posts
2,872,526
Members
156,431
Latest member
5ccarter3

Share this page

Top