Search results

  1. mpittman

    VHT Nightshade for taillights

    1. Remove light from truck 2. Mask off the reverse light (optional) 3. Scuff the original factory finish with 600 grit sand paper. This will leave a dull finish. 4. Clean light with alcohol, removing all finger prints, sanding dust, and contaminates 5. Spray 2 or 3 light coats of VHT or other...
  2. mpittman

    VHT Nightshade for taillights

    I plan to tomorrow. Sent from my iPhone using Tapatalk
  3. mpittman

    VHT Nightshade for taillights

    One guy I know used the same products and process, and he’s going on 4 years of looking like new. So, we’ll see. Sent from my iPhone using Tapatalk
  4. mpittman

    VHT Nightshade for taillights

    I know lots of people are not a fan of this, but I think it looks great. First attempt ever. 3 layers of VHT 4 layers of clear 1500 grit wet sand Meguiars compound with a Harbor Freight DA Polisher Meguiars Polish Meguiars wax Sent from my iPhone using Tapatalk
  5. mpittman

    Headlight condensation 10 minutes after brand new install

    I did not buy aftermarket lights, I broke my OEM lights open and rebuilt them. After putting it all together, I ran through a car wash. Only one of my lights fogged up. Turned out, I forgot to put one of the dust caps back on. I put the cap on, and no problems since. Sent from my...
  6. mpittman

    Zone 4" lift with bilsteins?

    Looks really good! I like that stance. Sent from my iPhone using Tapatalk
  7. mpittman

    Zone 4" lift with bilsteins?

    I see two rings exposed on mine, and I’m at 1.4” setting. I see one ring exposed on yours, so that should be the 0.7” setting. That first ring would be 0” factory height. Sent from my iPhone using Tapatalk
  8. mpittman

    Zone 4" lift with bilsteins?

    True.... maybe he got the 4/2 lift by mistake? Sent from my iPhone using Tapatalk
  9. mpittman

    Zone 4" lift with bilsteins?

    As someone else mentioned... the spring seat may be on upside down. That would raise it a little. Sent from my iPhone using Tapatalk
  10. mpittman

    Zone 4" lift with bilsteins?

    Looks great! Here’s mine. Sent from my iPhone using Tapatalk
  11. mpittman

    Zone 4" lift with bilsteins?

    My shop was a little perplexed about the bilstein lift as well. That’s exactly why I set them myself. I just know our setups sound really similar and I’m dead level with Bils at 1.4”. Most people are with a 4/3 lift. Sent from my iPhone using Tapatalk
  12. mpittman

    Zone 4" lift with bilsteins?

    Did you set the Bils yourself? I got a 4/3 BDS lift with Bilsteins at 1.4” I’m dead level in all four corners. I didn’t trust the shop to set my Bilsteins correctly, so I set them myself and told the shop not to touch them. They were an authorized BDS installer, so I did trust them with...
  13. mpittman

    Headlight Retrofit Progress!

    Here is my video: Sent from my iPhone using Tapatalk
  14. mpittman

    Getting flashed after my 4" lift

    I had no idea where to aim my lights. So, I used my Dodge Journey as a guide. I set my Ram lights to the same height at 25 feet out, then went for a drive. LOL.... I could barely see past the front of the hood. I came back and raised them up and just winged it. Took another drive. Met...
  15. mpittman

    Getting flashed after my 4" lift

    This worked for my 2015 1500. There are two holes with arrows, mine was in the other hole than what this video shows. Shine a flashlight down in the holes and you'll see the adjuster.
  16. mpittman

    Getting flashed after my 4" lift

  17. mpittman

    Getting flashed after my 4" lift

    Yeah, I just watched a video on how to do it. So simple. I just need to wait for darkness now to work on it. I adjusted them about one full ratchet turn lower, but I have no idea how far that moves them. Any suggestions? Sent from my iPhone using Tapatalk
  18. mpittman

    Getting flashed after my 4" lift

    so, I get flashed by oncoming traffic after my 4" lift. But, its not because my headlights are not aimed, its all the chicks raising their shirts because my truck looks so much better. No really... it could be the headlights, but I'm going to keep believing the first statement.
  19. mpittman

    HID

    I lifted my truck 4” and still run the stock halogen candles. I get flashed all the time on low beams. How would he be able to go a year and never get flashed? Sent from my iPhone using Tapatalk
  20. mpittman

    zone lift... what say you?

    Stick with the Zone.... friends don’t let friends buy Rough Country. [emoji23] It’s not worth saving a few bucks. Sent from my iPhone using Tapatalk
  21. mpittman

    So I am wanting to lift...

    Here’s my 4” BDS on 35”s. I have Bilstiens on the front at 1.4”. The front actually rose 5.4”. Most people ask if it’s a 6” lift? Sent from my iPhone using Tapatalk
  22. mpittman

    zone lift... what say you?

    Change the shock options on the website, you’ll see 2” and 3” options. Sent from my iPhone using Tapatalk
  23. mpittman

    zone lift... what say you?

    If you don’t mind the rake, then this 4” kit with 3” rear coils is all you need. Nothing else. You might upgrade to Zone UCA’s while you are in there and have it tore apart. Zone is a very good kit. Sent from my iPhone using Tapatalk
  24. mpittman

    zone lift... what say you?

    I don’t think I lost any ride quality with my 4” BDS and Bilsteins. I lost a little turning radius, but it doesn’t rub. Not sure why that is. Sent from my iPhone using Tapatalk
  25. mpittman

    Headlight Revolutions Supernova V.3 -anyone?

    Anyone running these LED’s for their Low beams? H11 How do you like them? Worth the money? Sent from my iPhone using Tapatalk

Latest posts

Members online

... and 6 more.
Total: 1,222 (members: 56, guests: 1,166)
Robots: 1,608

Forum statistics

Threads
195,472
Posts
2,870,668
Members
156,182
Latest member
mill

Share this page

Top