Search results

  1. abouttobeglue

    How to remove nut sert for tailgate assist?

    My deezee assist nutsert stripped out a while back and I chuckedbit, finally got a new one, how can it get the old nutsert out?
  2. abouttobeglue

    Hella halogen bulbs?

    Thinking about swapping my bulbs from Sylvania xtra vision to hella high wattage or 2.0s, anyone tried hella bulbs as an upgrade? Not looking to do LEDs, thought about sealights, but it seems can bus is hit or miss. Mines a 2016 with factory quads
  3. abouttobeglue

    Truck got rear ended can I swap bumpers?

    My 2016 lowered Express got rear ended at a stop light. Initial quote is close to 8k after they add for my sway bar. I have the factory dual exhaust bumper, thinking of seeing if I can swap this to the paintable bumper with no cutouts, and since my exhaust is fubared on the driver side...
  4. abouttobeglue

    Windshield washer nozzle not working

    My nozzles were barley spraying, both had broken, with nozzles not in it sprays fine, when I put the replacements from rockauto in it'd the same as before, any ideas? I put it back together and let it sit before I made it worse. Pump works fine, water shot both ends with no nozzels
  5. abouttobeglue

    Does cpo warranty cover manifold bolts?

    Started noticing a little tick at startup from the passenger side, wiggled the heatshield and noticed it was loose, driver side is tight. I bought the truck was a cpo, came with a Powertrain warranty up to 100k, anyone had this covered?
  6. abouttobeglue

    Anyone running a jlt intake?

    I took my kn 63561 intake off after 4 years and put the factory one back on. Got an itch to buy something, anyone running a jlt, I know they are proven on the 5.0 coyotes
  7. abouttobeglue

    Adjusting rear control arms?

    I've got the core upper and lower rear arms, and the illicit no cut brackets, i noticed my passenger side is a little bit further back than driver side wheel, whats the best way to get them even?
  8. abouttobeglue

    Exhaust tips sticking out a little or slight tuck?

    I put my proven ground direct fit muffler on yesterday, had to take a Sawzall to the tailpipes they were welded to the y pipe on my powerstick. Got a slight dilemma, got one tip just at the edge and the other a finger or two past. Any body got a preference or reason for one or the other? I'm...
  9. abouttobeglue

    Proven ground 5 inch tips installed

    Got them in Christmas eve, put em on this afternoon. Got the 121.99 special amrecian trucks had for tips and muffler, didn't do the muffler. Looks to be of good quality, welds on the tips and muffler set up are nice.
  10. abouttobeglue

    What can cause Front end shake?

    Started getting a shake at certain highway speeds, over 65 s, goes away at 70, starts back around 73. I thought it might be the tires needing balanced, went ahead and had the wheels swapped to a set of big horn wheels that have been in the garage. Seemed to lessen it some, but still there. Any...
  11. abouttobeglue

    New seat covers installed saddleblanket

    I was putting my coverking saddlebkanket seat covers in. Got it all finished up, noticed my passenger side seat won't recline. Appears I knocked the rod loosetrying to fish the elastic starps through. How do I take the plastic side and the lever and cover off?
  12. abouttobeglue

    Can I use ceramic spray on inside of windows?

    I just got done cleaning mine up, did 2 coats of the tw ceramic spray costing, i have an issue on the inside window fogging up because of the off gassing. Anyone used it on the inside with tinted windows?
  13. abouttobeglue

    Front driver side bottoming out

    I noticed im starting to hit the front wheel liner more frequently now on the driver side.
  14. abouttobeglue

    Anyone running doetsch technitro slammer

    Looking at ordering these, anyone had any experience with them?
  15. abouttobeglue

    Put some wagner oex brake pads on

    I got 56k on my 2016, starting getting some brake squeal. Ordered wagner oex front and rear pads from rock auto, strange looking design, they have channels cut in. So far no noise and much better braking. Front pads had about 1/3 left, rear pads had 2/3, almost left em, but figured hell, I...
  16. abouttobeglue

    Anyone got a part# for polyurethane front sway bar links for a 2/4 lowered truck

    My 2nd set of napa links has started to go to shit. Clunks all that good stuff. Anyone know what energy suspension part# line sup?
  17. abouttobeglue

    Is my bumper fixable bent no paint

    Had a german shepherd run out from the woods on my out my neighborhood, I hit the brakes hard as I could did my best to avoid him, I know he got clipped on the back, but thank God he didnt go under. He took off running, I let the owner know. Didnt look at my truck til later. No paint damage from...
  18. abouttobeglue

    Cracked foglight worth upgrading?

    Noticed the lens on my passenger foglight is cracked, didn't notice any waterz still works. Is it work upgrading, I have a 2016 express, halogen fog and headlights, have upgraded the bulbs, saw some yellow foglight housings, not sure how I feel about that
  19. abouttobeglue

    Think I figured out low speed rear end clunk, need help please

    Been getting a clunk from the rear, low speeds up to 30 over bumps. Thought is was the spohn panhard where it flexed, put on a core bar, and new kyb gas ajust shocks, still there. Figured the rear control arms were worn, just finished putting on core 4x4 upper and lower rear arms still there...
  20. abouttobeglue

    Anyone use inez hot rods rear control arms?

    Torn between ordering these for 300 for the full set or just the core 4x4 lowers. My core 4x4 panhard bar is awesome. Noticed clunking on my rear passenger side, pretty sure one of lower bushes is shot.
  21. abouttobeglue

    Going to cut the bumpstop cups off, how where do I put the new universal ones?

    Going to cut the bumpstop cup off my truck in the next 2 or 3 days to hopefully fix where the cup hits the control arm. I've got some energy universals, I see a hole at the top but no way to get to the other side and 2 holes on the bottom porch. Do I need to get nutserts or rivnuts?
  22. abouttobeglue

    Busted an airlift bag/they have awesome customer service

    Put in my nitro drop 2 shocks, was airing the bags up to from 5 to 30 psi, driver side 2 seconds and fine, passenger side 2 seconds and boom....well shit, this is gonna cost me money. Any recommendations for other airbags/helpers for a belltech 2/4 with the illicit no cut relocation brackets?
  23. abouttobeglue

    DO I need new shocks?

    Bout a month ago started getting some vibration from what feels like the right rear, had the tires balanced no change, had the factory good years put on, had the same shop that did my alignment and tierod shortening, they adjusted the alignmentsome, not much difference on the road. Today I put...
  24. abouttobeglue

    Uneven tire wear causing vibration?

    My front tires have worn out more on the middle to outer edge than the inside, I'm assuming it's from being lowered and not being able to get everything fully in spec. Noticed over the past 2 weeks its getting to wear it shakes/vibrates over 40ish. Wondering if I should put the goodyears back...
  25. abouttobeglue

    Any one running a Single din radio with built in mic?

    Been looking at upgrading my radio, I have the base 3.0, I did upgrade to the mopar/kicker speakers all the way around. Only thing I'm really wishing I had was hands free calling and bluetooth streaming. I have a bluetooth mic that plugs into aux port that works ok, but it's annoying to use...
Top