Search results
-
Stock 5.7 dyno numbers???
I know this old, and granted none of these trucks were new except some 2014s every thing after 2014 were new at the time.. I've only done two 2003's one RC4x2 and the other QC4x4 , the 4x2 hit 281, the QC barely made 260. Most of the bone stock 04-05s I've dynoed were 270-280. 06 -08...- ric3xrt
- Post #7
- Forum: Engine & Performance
-
Cam failures or not. How many miles have you gone?
Anything over 11MPH (17KmH) on the 1500s the MDS is active when your foot is off the pedal... and again it's hit or miss, there are plenty of cam failures with less then 100 Idle hours, and many with above. it's not an absolute defined issue, just read thru the comments in this thread, almost...- ric3xrt
- Post #99
- Forum: Engine & Performance
-
Cam failures or not. How many miles have you gone?
LOL nice one , I'm sure there's good stand up comedy spot near you.- ric3xrt
- Post #91
- Forum: Engine & Performance
-
Cam failures or not. How many miles have you gone?
LOL it's long idle durations that hurt the cam/lifters when in ECO/MDS activation. normal driving its fine, stuck on the 405 Freeway for 30 mins...your fine, an hour no , but it's not like that one hour is going to hurt you, it's the 20-30 hours a month that add up is where we see the damage...- ric3xrt
- Post #90
- Forum: Engine & Performance
-
Cam failures or not. How many miles have you gone?
A lot of it is blown out of proportion, when you look at it from a Per/100 warranty claim , Dodge averages .71 units for every 1 GM..... a good friend of mine is very high up on the Ford Corporate food chain , and says they are starting to see a few of the same type cam failures with the all...- ric3xrt
- Post #72
- Forum: Engine & Performance
-
Check out my new Aluminum 468 for my Daytona
You ever finish this truck ?- ric3xrt
- Post #341
- Forum: Engine & Performance
-
Sell or not to Sell....
Only you can decide if it's worth it, if you sell it, the 1st nice GoManGo Daytona you wish you had yours. these trucks seem to hover around 8500-12k in good shape, with it ever be worth the same as your Father in Laws 69.......probably not. I tell my friends and people I've built engines for...- ric3xrt
- Post #8
- Forum: General Discussions
-
Superchips 3865 Trans Tuning
I'm in the same boat but the guy I talked to told me I had to buy a new one...I'm going to try again next week.- ric3xrt
- Post #8
- Forum: Engine & Performance
-
-
-
Ric's G3 Hemi Videos
They can be a ***** to put back together , I'm going to do one on different way to modify them , I have trick that moves the sweep, and I'll so how to lock them with out the Comp cams piece. -
How-to: 4th gen Ram/GM transmission (4L80e) swap
it's a route to that can be taken, but the 518/46Rh is bolt in, stock X-member ,stock driveshaft......no doubt about it none of these guys are making enough HP&TQ to hurt a 727 and Gear Vendors combo....- ric3xrt
- Post #47
- Forum: 4th Gen DIY
-
How-to: 4th gen Ram/GM transmission (4L80e) swap
Look in to a 518/46rh swap, it's BOLT in , no adapters, the con of the 46rh swap is it's only 4 gears but you can control the lock up of the converter . ..................- ric3xrt
- Post #45
- Forum: 4th Gen DIY
-
Ric's G3 Hemi Videos
I did a Video a few weeks back on the VVT phaser. -
-
Check out my new Aluminum 468 for my Daytona
You guys are in Texas ?- ric3xrt
- Post #334
- Forum: Engine & Performance
-
Check out my new Aluminum 468 for my Daytona
I forgot to quote op, I was asking him if it was powdered , I know you spray caned yours(LOL)- ric3xrt
- Post #327
- Forum: Engine & Performance
-
Check out my new Aluminum 468 for my Daytona
Looking Good, did you have the timing cover powder coated ?- ric3xrt
- Post #325
- Forum: Engine & Performance
-
-
-
G3 Hemi Videos
I started to post some Videos on the G3 Hemis the latest is general on oiling . thanks to all who have watched- ric3xrt
- Thread
- Replies: 1
- Forum: Photos & Videos
-
2003 4.7l swap to 2003 5.7L
X2 on Ebay also try http://www.car-part.com Not sure if you do facebook but there are few real good groups there that might be able to locate one for you. -
Ric's Hemi Videos
This new one is on Oiling....thanks to all that have watched- ric3xrt
- Thread
- Replies: 3
- Forum: Photos & Videos
-
Rocker Video
This one shows the Interference with using Eagle Heads and Intakes on the pre eagle blocks -
2003 4.7l swap to 2003 5.7L
Both trucks being 03 you will be fine. The instrument cluster is the same for in 2003 for 3.7/4.7/5.7/5.9(V8)8.0(V10) trucks the odd issue is Manual door locks vs Power Locks..Not sure what the deal is, I just know there were/are two different instrument clusters. It's the under hood...
