Search results
-
AlfaOBD
I agree with you i disagree. By providing us with a simple service as looking something up on a pc will guarantee the business to be called upon when needed by forming a trust between customer and service provider- Thomas Caccitolo
- Post #14,213
- Forum: 4th Gen DIY
-
AlfaOBD
It did that to me initially. I had one of the pins on the wrong socket- Thomas Caccitolo
- Post #14,212
- Forum: 4th Gen DIY
-
AlfaOBD
Then why doesn’t someone clean this thread up and delete them?- Thomas Caccitolo
- Post #14,207
- Forum: 4th Gen DIY
-
AlfaOBD
You have no need for the Pwm modules. Just change setting in Alfa- Thomas Caccitolo
- Post #14,205
- Forum: 4th Gen DIY
-
-
-
AlfaOBD
Ya. I don’t understand what worth gridlines would have looking at your bed- Thomas Caccitolo
- Post #14,202
- Forum: 4th Gen DIY
-
AlfaOBD
I have the exact same cam and go figure I mounted it in the exact same spot- Thomas Caccitolo
- Post #14,201
- Forum: 4th Gen DIY
-
Alpharex
Maybe just a coincidence but I’ll try another headlight switch. I’ve already tried switching out the sun sensing module on the dash.- Thomas Caccitolo
- Post #5
- Forum: Exterior
-
Alpharex
It’s not an option to go back to the original halogens. Thx for the reply though.- Thomas Caccitolo
- Post #4
- Forum: Exterior
-
Alpharex
Hi all. I’ve recently installed alpharex headlights to my 14 slt. It originally came with halogen quads. I’ve upgraded to LED bulbs in the high & low beam. They’re working fine but since this install my auto on is just plain ON. Any idea how to fix this? I’ve used alfaobd to change settings to...- Thomas Caccitolo
- Thread
- Replies: 5
- Forum: Exterior
-
-
high output alternator
I use Mechman 370 amp. Need a half inch smaller serpentine and some meatier cables & you’re good to go- Thomas Caccitolo
- Post #26
- Forum: Audio & Electronics
-
-
Power Inverter Seat Harness Part #
I have the wire behind the dash bezel so I’m assuming there’s one going to the seats. Is it under the carpet?- Thomas Caccitolo
- Post #3
- Forum: Interior
-
7" lift - 5th gen / RWD/ 2 piece driveshaft - do I need carrier bearing kit?
You definitely need to line all that up. Tranny to differential should be a straight line.- Thomas Caccitolo
- Post #34
- Forum: Lifted
-
Inverter wiring?
How can I tell if I have inverter wiring present in my 14 slt? Is it hidden under the passenger seat carpet? I have a connector that’s plugged into a dummy port on the right lower side of dash bezel. My slt did not come with seats with inverter.- Thomas Caccitolo
- Thread
- Replies: 1
- Forum: Interior
-
-
Retro fit headlights
I’m talking about converting- Thomas Caccitolo
- Post #3
- Forum: General Discussions
-
Retro fit headlights
Anyone ever retrofit these aftermarket’s with high beam and low beam led’s? I had quads, converted to hid projectors, now I wanna go led hi/low beam. I got an Alfa obd. What else is needed?- Thomas Caccitolo
- Thread
- retrofit aftermarket headlights
- Replies: 4
- Forum: General Discussions
-
Under hood lamp.
That bulb doesn’t sit flush in the housing to shine down- Thomas Caccitolo
- Post #6
- Forum: Exterior
-
2.5" rear spacers to 4" coils
- Thomas Caccitolo
- Post #16
- Forum: Lifted
-
Replacing rear coil spring
I’m running bilstein 5160’s on the rear- Thomas Caccitolo
- Post #4
- Forum: Lifted
-
Replacing rear coil spring
I have rough country 6” suspension lift on my 14 slt rwd. I’m looking to replace stock rear coils and the 4” spacer with just coil springs. I have Hellwig 7883 sway bar on the rear as well. I wanna remain at level height. Can anyone recommend a spring for this?- Thomas Caccitolo
- Thread
- Replies: 3
- Forum: Lifted
-
Wiring
Hello. I’m looking for someone current who can point me in the direction of bcm to heated/ventilated/power seat harness- Thomas Caccitolo
- Thread
- Replies: 0
- Forum: General Discussions
