I am going to clean the filter and maf sensor today and check the brakes. Might be a silly question, but what exactly does brakes dragging look like? or what is that? yeah definitely made sure I am back in 2wd.
I went to an off-road park over the weekend where I tried a few obstacles and played in the mud a bit. Nothing major to say the least. On the way home the drive was real shaky due to mud caked in the wheels etc etc. I spent a couple hours underneath and cleaned up what I could that fixed that...
I purchased some alpharex headlights for my.17 with stock quad headlights. I installed the lights and everything works except the turn signals. The dash is giving me a no turn signal message. Is there a setting I need to change through alpha obd? Thanks in advance.
So about a week ago I installed a small airhorn behind the grill. I zip ties the compressor to what I know now is a air flow regulator. Small vents that move up and down. So it made my check engine light come on. I took it to the dealership to pull code and replace if needed. Of course the want...
So I fixed the issue and tapped into the line so now my front door and dash speakers work powered by the radio going through the Lc7 and amp. No audio out of my tears tho. I should be getting the LGD tomorrow
Yeah I didnt think about that so I will fix that when I get the load resistor.. I went with Cerwin Vegas all around. I also have a Kicker 750.1 amp for the subs that I didnt put in yet.
Okay I will do that for the sub. Yes I've played with the knobs to make sure they werent turned down. Do you think my dash speakers will work that I cut into the harness or will I have to run new speaker wire to them as well?
Alright guys here's an update. I plugged directly into the amp and all speakers except the dash worked. I was planning on running them from the HU so I didnt expect them to work anyways. I disconnected the battery for about an hour while I did some things around the house. Plugged it back up and...
Ok I'll take some pics for you by tomorrow. I originally didnt have a remote wire becuase I knew it would turn on when sensing signal. I wonder if that's causing the problem. I have RF r600-4d. I have to be up early for work tomorrow so I'll def take pics of everything.
I have this 5 pair conductor cable so I tapped into every speaker wire (4 channels) and connected them straight to the Lc7. I jumped right rear door I believe and sent it to the sub channel.
I installed a 8.4 radio the week before. While installing I noticed my backup camera was aftermarket so there is a harness that connects to factory connector. I tapped in from the harness radio side and ran it back to the lc7. I have a 4 channel Rockford fosgate amp. I checked the gains and I...
Ok so I installed all new speakers (6 in total). I ran from the HU directly into an LC7 then to amp and finally to speakers. I got power and everything looks good and bam no sound. I'm now seeing that I may need to install some resistors to let the radio know theres speakers?? I'm kind of at a...
Thanks for the input guys. I have the non alpine system so I'll tap everything from the back of the hu. I ran the dash speakers to the hu and will run the doors to the amp since I have a 4 channel and a mono for the subs.
Upgraded to the 8.4 this past week and notice the hands phone audio is barely audible. I can have the audio maxed our and still the phone call is extremely low. I couldn't find any options in the settings. Does anyone know a solution for this?
So I have the non alpine 6 speaker system and will hopefully be installing a system this weekend. I have 4 channel amp for the doors and a mono amp for subs. I purchased an Lc7 to hook up to my new 8.4 . So this is my plan. I'm going to let the radio power the tweeters and run the doors to the...
Ok, so I tried the settings you mentioned. Didn't seem to work. So I took some screenshots of everything i have currently set. Please let me know if i have anything incorrect.
I bought my truck some odd months ago and noticed i never had backup camera grids. So I installed some side mirrors with turn signals and enabled them with ALFAOBD. Worked like a charm! Ive noticed there are many camera options and grids that could be enabled. Ive tried a few of them and was...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.