Found a power driver seat on eBay, color and fabric matched to what's already in my truck. All hooked up and working, so far it's quite a bit better than manual, especially the adjustable lumbar.
Thank you... Before I start pulling new wires and tearing out the old seat - I am comparing the connectors under the powered seat with the connectors under the original seat. I notice that the powered seat has an extra gray plug with one black wire, that my original seat does not have. What is...
I will be replacing my front driver manual seat with a powered seat (no heat, no cooling, no memory). The connector under the seat on my SLT apparently does NOT have the 12v power that is needed. What is the recommended gauge wire if I want to run the power from the battery to the connector...
Is this considered "10 way" adjustable?
-raise
-lower
-forward
-back
-tilt seat up
-tilt seat down
-recline forward
-recline backward
-lumbar in
-lumbar out
I have a 2014 SLT QC with manually adjustable cloth gray seats. In short, they SUCK. It's not that they are worn out or torn or anything. I just cannot get the correct position/support. I've tried adding foam lumbar support, and even mounting spacers attempting to raise/tilt them.
I'm at the...
Mystery solved by taking an angle grinder to the back side of the new lift spindles. Was easily able to get 45 degrees more rotation on the steering wheel in each direction!
BEFORE:
AFTER:
Hmm I don't notice it being "very sloppy". I like the ride much better than just front level springs. After a few weeks I'm almost adjusted to making a bit wider u-turns and navigating parking lots.
** SOLVED **
2014 RAM1500 2WD
I installed RC 2.5" level (springs) almost a year ago. Everything was normal except a rough/stiff front end and some bump steer on uneven roads.
A few days ago, I had a local shop install RC 4" lift (stock springs, front spindles, rear spacers, 4 new shocks). I...
I installed full power mirrors (chrome cap "limited"), plus door modules and switch.. Programmed with alfaobd, and they work great (when paired with a back up camera). If you don't have a backup camera, I could understand how it wouldn't be a good feature.
Thanks for clearing up where pins 29/30 are in relation to other pins, except why are the numbers in your diagram flipped upside down from the diagram from connectors.dcctools.com? And, do you think I am risking damaging the microphone port on my aftermarket radio by feeding the oem mirror...
So if I want my side mirrors to dim, I could get the 911/Assist AutoDim rear view mirror 68096091AF + covers. Would I need a different wiring harness?
Wow, love that link! Says pins 29 and 30 are for the microphone. The diagram points out pin 31-40. But is pin 30 directly "below" pin 40, or is...
I have a stupid question... I added chrome cap "limited" power fold, tilt reverse, turn signal, dimming side mirrors (non-tow) to my 2014 SLT that originally had regular mirrors and RA2 radio and (manual flip to dim) rear view mirror. I set all the necessary AlfaOBD codes, everything works but...
Replaced my RA2 with aftermarket+idatlink, DRL option is showed right up with everything else on the new radio. No idea why it refused to show on the RA2. Oh well, goodbye RA2 hated it.
I just did RA2 to aftermarket in my 2014. Since I'm on a budget, I went with 6.8inch screen aftermarket and kept my current bezel and AC controls, then just use iDatalink Maestro to enable steering wheel controls and oem car features. Go to Crutchfield.com they have it all.
I got a full set of OEM black/unpainted fender flares from a local guy on OfferUp. Turns out they are for 2500, so the front flares do not go down to my 1500 bumper. So looking to buy ONLY the front 1500 OEM flares, or can trade these 2500 front flares for 1500 front flares.
Thanks
Mike
95206
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.