AeroForce Gauges

[3rdStrikePerformance]

How to hook up the AeroForce gauge...

1. Make sure the car’s ignition is turned off.
2. Run included 5’, or optional 9’ main cable, and three wire mini cable, from
the OBD2 connector (do not plug in yet) to the location of the Interceptor(s).
The Interceptor will fit in any 2 1/16” or 52mm gauge pod, or can be mounted in
a custom fashion anywhere within 5 (9) feet of the OBD2 connector. The OBD2
connector is located under the dash on either side of the steering column.
3. Plug both cables into the back of the Interceptor. See figure 1. Press the
Interceptor(s) into the gauge pod or mounting hardware.

 

[ramthis9501]

Your doing great , I hope the members are not just making you find items for fun and are actually buying those items .

I promise you I'm not. I'm just looking at my options, but it's not looking to promising because I don't think that any oem one that I get will read my mileage.

 

[cheapbeater]

Duane- does the interceptor read trans temp through the obdII port on an '03? or will it need a seperate sensor?
thanks

 

[3rdStrikePerformance]

I promise you I'm not. I'm just looking at my options, but it's not looking to promising because I don't think that any oem one that I get will read my mileage.

I think you will find the replacement gauge units I put on the site for you will fill the bill. They seem to be pretty easy to install....

 

[3rdStrikePerformance]

Duane- does the interceptor read trans temp through the obdII port on an '03? or will it need a seperate sensor?
thanks

I would assume it would read it through the OBDII Port also...but I will email them tomorrow about it.

 

[cheapbeater]

sweet! thanks. ive always wanted one but could never get a clear answer on this...

 

[KGBIGCOUNTRY]

I noticed its sopp to read trans slip also which is even a better bonus because I think mine is slipping at shift at WOT.

 

[3rdStrikePerformance]

I noticed its sopp to read trans slip also which is even a better bonus because I think mine is slipping at shift at WOT.

yep. Hell of a gauge for the money....

 

[KGBIGCOUNTRY]

Duane just ordered an AI cant wait to get it and hook it up.

 

[3rdStrikePerformance]

Duane just ordered an AI cant wait to get it and hook it up.

Got it. As soon as Aeroforce opens back up, I will get it on order for ya. Thanks!

 

[KGBIGCOUNTRY]

Cool, are they off for the holidays? If there off for awhile I may change the shipping addy, just PM me like before.

 

[3rdStrikePerformance]

Cool, are they off for the holidays? If there off for awhile I may change the shipping addy, just PM me like before.

I'm not sure buddy, but I just got your information earlier, and when I tried to call, they didn't answer, so I assume they were closed today. A lot of them are....one of them - Grille Craft - is closed until the 3rd~~

 

[3rdStrikePerformance]

Guages are supposed to be shipped tomorrow....as soon as they come in, I will ship yours to you.

 

[KGBIGCOUNTRY]

Shooting you a PM...

 

[3rdStrikePerformance]

Well, the gauges arrived yesterday, but they sent the wrong cables, so I had to call them and tell them. They are sending the correct ones out asap, so I should be able to send the gauge to you early next week.

 

[KGBIGCOUNTRY]

Thanks, replied to your Pms thank you for keeping me in the loop. You have had great customer service and look forward to ordering more.

 

[Redtruck-VA]

I would assume it would read it through the OBDII Port also...but I will email them tomorrow about it.

Guys, I have the AF Interceptor, w/wideband on a 03 and yes it is plug and play. One of my better mods.

 

[Redtruck-VA]

Duane,
I'm looking for a 300 psig pressure sensor kit to use with my AF Interceptor gage. Any suggestions?
Thanks,

 

[3rdStrikePerformance]

Duane,
I'm looking for a 300 psig pressure sensor kit to use with my AF Interceptor gage. Any suggestions?
Thanks,

I will email the owner and see what he suggests.