Thuren Level Kit Setup

[G. Mcpherson]

One more Pic today. Clay bar and two coats of Rejex Sealant. Rain starts today here.

 

[Phil21502]

Looks good. 3' front coils?

 

[Phil21502]

Oh and how much lift did u get in the rear? Thanks

 

[zeddy]

View attachment 92507

View attachment 92508[/attach]

A couple more.

I love the wheels....

 

[G. Mcpherson]

2" Front coils. I got about 2 1/2" front and 1"rear. Actually just measured the other day and the Front settled to about 2 1/4". Thanks! It wasn't my first choice but I do like them.

 

[sharkfinn]

I just ordered my 2" kit today and cannot wait to have it installed. New wheels and 35's are on order.

 

[G. Mcpherson]

Rear Track Bar installed today. Pic tomorrow.

 

[G. Mcpherson]

Here is a couple shots of the Track Bar. I have the Rear Coils also and this makes the ride so much smoother without the springing side to side. Well worth the investment as to complete the changes.

 

[Ratket]

Ok McPherson, what all do you have done so far as suspension or should I say Thuren stuff lol.

 

[G. Mcpherson]

OK! Front 2" Coils along with the Track Bar. Also Front End Links. Had to get Different Front Shocks. Bilstein. 1" Rear Coils and End Links. Rear Track Bar. Most likely going to get the Front Sway Bar. Also Replaced Rear Shocks. Bilstein. All this has really changed the Ride and Feel of my Truck. Going to tow my Trailer in a couple of weeks and should be a noticeable difference.

 

[Ratket]

Is ur truck gas or diesel?
Also when you say 1” rear coils did it lvl it or give it a little rake?

 

[Phil21502]

I really want the rear coils but want zero rake. I have the 3" thuren front coils now. Wish they made like 1/2" lift rear coils

 

[sharkfinn]

I really want the rear coils but want zero rake. I have the 3" thuren front coils now. Wish they made like 1/2" lift rear coils

Can you post pics of your truck with the 3" level on the front? What are the front and rear height measurements? I wanted to do the 3" but had read that the tuck might sit nose high.

 

[G. Mcpherson]

My Truck is the 6.4. I now have a 1" rake with the rear coils. They actually measure before install about 4.5" taller than factory coil. 43" front and 44" rear.

 

[Gear Jammer]

I have the Thuren 3" coils in the front, and stock springs in the rear. On my tuck the front sits about a half inch higher than the rear, with all four tires at 70 PSI. I will be adding the rear coils in a couple weeks.

 

[Phil21502]

Can't wait to those measurements with the rear coils. It's a hemi?

 

[Gear Jammer]

Mines the 6.4 Hemi. I'm also still running the stock tires, once they wear down a little more I'll be going bigger. Hopefully I'll be ordering the rear coils in two weeks.

 

[Phil21502]

Keep me updated. Wish they would only give 1/2" of lift

 

[SwollenMonkey16]

I have the Thuren 3" coils in the front, and stock springs in the rear. On my tuck the front sits about a half inch higher than the rear, with all four tires at 70 PSI. I will be adding the rear coils in a couple weeks.

Hey brother I also have a long bed. Did those 3" springs make a huge difference in ride quality? I'm also on the fence between using a spacer or springs for the rear also.

 

[Gear Jammer]

I wouldn't say that the front springs made a huge difference, but the difference was noticeable. If I had went with better shocks, instead of the Thuren Overland shocks, I think the difference in ride would have been more noticeable. I'm probably going to run Bilstiens in the rear when I get the rear lift springs. In my opinion, the front springs are definitely worth it. One thing, with the overland shocks, joints in a concrete freeway got worse.