What did you do with your 4th Gen this week?

[TotallyHucked]

Crawled up underneath to see why my E-brake doesn't work, found my cables were completely loose and just dangling. So now I've gotta figure out why...



Then I started de-striping and de-badging. Only got the driver's side done cuz my heat gun decided to die on me






Added some wax and it looks soooo much better. Going to replace that Hemi badge with a black one and call it good

 

[TotallyHucked]

Also upgraded most of the lighting this weekend. Auxito makes the best LED replacement bulb I've found so far, their LED chips are as close to the same location as the filament in a halogen bulb as possible and the board is super thin, so they work perfectly in factory non-HID projectors. Used them for my lows and also for the high beams. One thing I didn't realize was the body on these is non-adjustable, so I had to finagle one of the tabs in first and rotate it 90* from where they'd normally install to get them in the proper up and down orientation. I left the high beams as they came (sideways) and the beam pattern is funky, so I'm gonna have to do the same there.




Also installed new fog light assemblies since one of my lenses was cracked. Took a chance on these since they had good reviews and they are fantastic. Very wide pattern, they throw a good distance and also have a nice cutoff. I went with the black ones to match the dark sport lights and they're not obnoxious looking at all

 

[TotallyHucked]

Also added the DeeZee tailgate assist


And some LED tag lights



And some spot mirrors that fit our sport mirrors very well, though I put them in the bottom corners




So now I'm just waiting for the DieselLEDs reverse lights to come in and then find time to tackle the interior lights.

 

[Socalramfan]

Also added the DeeZee tailgate assist
View attachment 517394

And some LED tag lights
View attachment 517395
View attachment 517396

And some spot mirrors that fit our sport mirrors very well, though I put them in the bottom corners

View attachment 517397
View attachment 517399

So now I'm just waiting for the DieselLEDs reverse lights to come in and then find time to tackle the interior lights.

You‘ve been busy

 

[MileHighRam11]

Got these puddle lights/signals. Stock passenger side was out for as long as I remember so figured spending $50 wasn’t too bad. Nice smoked look to them.

 

[Justthebutler]

Got these puddle lights/signals. Stock passenger side was out for as long as I remember so figured spending $50 wasn’t too bad. Nice smoked look to them.

I like the solid led look, those are nice!

 

[WY-Dave]

Went to the depot and got some shelving. Redid the HazMat area. Got some old gun lockers from Bro-in-law


The old HazMat area


Had to move the Toolbbox(next pic) so the workbench goes bye-bye until I get the lil stacked toolbox from the shed
I def have too much stuff, 9000w HF gen, 2500 HF mini gen, 21 gal compressor, gas power washer and the 5th wheel hitch


end of 2 day ordeal not fini here

 

[Bandit517]

Crawled up underneath to see why my E-brake doesn't work, found my cables were completely loose and just dangling. So now I've gotta figure out why...
View attachment 517372

Look into the actuator cam at the axle. They commonly get a bit of rust/road grime on them and not release fully. To this day mine still hangs a little low because the cam isn't perfect. But the e-brake isn't dragging so I don't worry too much about it.

 

[MileHighRam11]

I like the solid led look, those are nice!

Not too bad! Off eBay from vipmotoz.

 

[Justthebutler]

Crawled up underneath to see why my E-brake doesn't work, found my cables were completely loose and just dangling. So now I've gotta figure out why...

Mine was like that also, I think its a common issue. When I took it to my shop for a full brake job, they replaced the cable and everything because of how rusted it was.