Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Registered members
Current visitors
Dodge Ram News
Forum Rules
Log in
Register
What's new
Search
Search
Search titles only
By:
Registered members
Current visitors
Menu
Log in
Register
Install the app
Install
RAM TRX - TRX-Forum.com
Bronco Raptor - BroncoRaptorForum.com
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
jws123
Senior Member
·
From
nj
Joined
May 16, 2018
Last seen
6 minutes ago
·
Viewing thread
Electric Power Steering FIXED- READ FOR SOLUTION
Posts
2,100
Reaction score
2,021
Find
Find content
Find all content by jws123
Find all threads by jws123
Latest activity
Postings
About
jws123
replied to the thread
4.7 Exhaust manifolds
.
Just sand your original manifolds flat they will never warp again I used a harbor freight belt sander or if you can find a local machine...
Friday at 10:21 PM
jws123
replied to the thread
2004 Ram doesn't like ot shift into drive
.
when is the last time ya changed the trans fluid/filter.
Friday at 9:13 PM
jws123
replied to the thread
2004 Ram doesn't like ot shift into drive
.
Is it when you first start it? I know on older rams if you fire it up and put it right into drive it takes a second better to let it run...
Friday at 9:00 PM
jws123
reacted to
crash68's post
in the thread
Dead Truck
with
Like
.
There's a wiring harness under the truck, inside the frame rail near the back of the front tire, check to make sure it's not sperating...
Friday at 8:30 PM
jws123
replied to the thread
Intermittent power steering problem at slow speed or stopped.
.
Open hood turn wheel make sure the belt is not slipping on the pulley. Also you should flush the system I usually use lucas power...
Friday at 8:28 PM
jws123
reacted to
rzr6-4's post
in the thread
DRIVE SHAFT TWISTED SNAPPED IN HALF
with
Like
.
If a shop willingly covers the cost, either A) they screwed up the installation or B) the part was faulty from the manufacturer and they...
Friday at 8:25 PM
jws123
replied to the thread
New Ignition with codes
.
did he program a new key to it or just cut a key? you might also want to try unhooking both battery terminals off the battery and then...
Friday at 8:23 PM
jws123
reacted to
jeovanicorro's post
in the thread
4.7 oil pressure sensor
with
Like
.
swapped it and so far it works good now my only problem now is that when it gets warm and i turn off the truck it won’t start back up...
Monday at 10:45 PM
jws123
replied to the thread
4.7 oil pressure sensor
.
Pickup tube was clogged at hot idle like yours it lost oil pressure wound up rebuilding lower end bearings new pump ect.
Monday at 7:53 PM
jws123
replied to the thread
4.7 oil pressure sensor
.
10w40 is to thick for these 10w30 is ok but yea that wasnt a good thing not replacing the oil pump lol you may get stuck doing that.
Monday at 6:50 PM
jws123
replied to the thread
2005 Dodge Ram 1500, I heard a ding twice and then my instrument cluster stopped working, also temp display shows 130 and A/C compressor don't kick in
.
Unhook battery for a while check and clean all grounds and connections open fuse box look for signs of corrosion/melted plastic check...
Monday at 8:31 AM
jws123
reacted to
Docwagon1776's post
in the thread
Newbie struggling with truck choice
with
Like
.
Here's one meeting your original criteria and it's in Illinois...
Monday at 8:10 AM
jws123
replied to the thread
Newbie struggling with truck choice
.
Be willing to walk away remember they are desprate not you lol invetory is full everywhere often they will call you back the next day.
Monday at 8:10 AM
jws123
replied to the thread
4.7 oil pressure sensor
.
Yep I just had this issue on a 2006 I was working on its 1 of 4 things. Your sensor is shot replace it. Your pickup tube is clogged...
Monday at 8:08 AM
jws123
replied to the thread
Newbie struggling with truck choice
.
mine had 180k before I did the camshaft I replaced the chain but could of re used it so your good just make sure it doesnt have lifter...
Apr 21, 2024
Loading…
Loading…
Latest posts
B
Videos changing From H11 to H9 and from H9005 to H9011 ?
Latest: bcraig
A moment ago
Exterior
What did you do with your 4th Gen this week?
Latest: audiophile
2 minutes ago
General Discussions
J
Center Axle Disconnect Vacuum Issues?
Latest: JimJam300
19 minutes ago
General Discussion
I just changed my spark plugs to NGK copper and it still runs rough. 5.7
Latest: GTyankee
22 minutes ago
Engine & Performance
TOSS-UP HELP
Latest: Dodge 1500 4X4
28 minutes ago
Engine & Performance
Staff online
rule18
Admin
Members online
bcraig
rule18
seems fishy
18CrewDually
Pears
Maniac
Rufi
JimJam300
CRS1968
audiophile
BDay2351
AZ MARK
randygrove
jws123
Demon13
zstroken
JungleRat
keltek
dalcini
16Crawler
PoMansRam
KalboKalbs
northlane1
Curmudgeon
yogibear18
GNiK
pacofortacos
Scubadvr
s_wall98
Dodge 1500 4X4
Ramhemi12
Hemi832
CanuckRam1313
GTyankee
enuser
hdog33
Kickboxer
OnlyCesar
crackerjack1957
Lvsparky
stexram
TomT
... and 1 more.
Forum statistics
Threads
195,687
Posts
2,873,327
Members
156,558
Latest member
zstroken
Share this page
Facebook
X (Twitter)
Reddit
Pinterest
Tumblr
WhatsApp
Email
Share
Link
Members
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top