Recent content by STecoD
-
Driver's seat harness
It looks like the plug for your center seat or console. 12v plug in the middle. CD player if you have one. Sent from my iPhone using Tapatalk -
-
Hello All, my first time asking question here.
If you have the 15 seats in your truck you would have to rewire the plug on the seat or on the truck. It doesn’t plug in. If you put your old seats in then you might not have them plugged in all the way. Your question was a little vague so I was trying to answer as best I could. Sent from my... -
Towing mirrors
With AlfaOBD you can turn them on yourself. If you go to the dealer just tell them you installed tow mirrors and you need them turned on. Sent from my iPhone using Tapatalk- STecoD
- Post #2
- Forum: 4th Gen DIY
-
How To: Add Factory Keyless Enter N Go
I put a 2017-2018 hub 68319680AD in my moms 2014 Truck. Works good. Sent from my iPhone using Tapatalk- STecoD
- Post #902
- Forum: 4th Gen DIY
-
AlfaOBD
I put a 2017 hub in my moms 2014 truck and a 2016 in my 2015 truck. Works great. I used the 2016 in my truck because I already had the remote antenna. Sent from my iPhone using Tapatalk- STecoD
- Post #7,552
- Forum: 4th Gen DIY
-
How To Add Heated/Ventelated seats and Heated Wheel to Express/Tradesman
For memory seats you will need seats from a Laramie or a truck that had it. The motors in your sport are not setup to track the position you would need a memory module and a wiring harness and at least the motors swapped out on your sport seats. Sent from my iPhone using Tapatalk- STecoD
- Post #1,646
- Forum: 4th Gen DIY
-
How To: Add Factory Keyless Enter N Go
If you pull the tub of your center console out then you can fish the antenna wire into there and mount it on the inside of the center console. I mounted mine on the back right side and my moms in the front near the other wires. Dealers choice. Wanted it in a place I could program my fobs easily...- STecoD
- Post #716
- Forum: 4th Gen DIY
-
AlfaOBD
You can get it to work no problem. You have to have the memory mirrors normally chrome capped. Sometimes the door modules need to be swapped out. I have a couple that I can sell if you do end up needing them. The mirrors are needed first. The memory mirrors will have more than 4 wires in the...- STecoD
- Post #7,356
- Forum: 4th Gen DIY
-
How To Add Heated/Ventelated seats and Heated Wheel to Express/Tradesman
So if you get seats you can have the lights under the rear seats. You would have to add wiring to get the heated seats. Sent from my iPhone using Tapatalk- STecoD
- Post #1,633
- Forum: 4th Gen DIY
-
How To Add Heated/Ventelated seats and Heated Wheel to Express/Tradesman
If you lift up the back seat there is one on each side. On the frame. Little grey 6 pin plug. Sent from my iPhone using Tapatalk- STecoD
- Post #1,631
- Forum: 4th Gen DIY
-
How To Add Heated/Ventelated seats and Heated Wheel to Express/Tradesman
Depends on your truck. The easiest way is to look at the plug under the rear seat and see if you have 5 wires, 2 wires, or no wires plugged in back there. If you have the 5 then it will plug and play with the right center console wiring and switches on the back of the console. Sent from my...- STecoD
- Post #1,629
- Forum: 4th Gen DIY
-
How To Add Heated/Ventelated seats and Heated Wheel to Express/Tradesman
Rear heated seats plug. I had to install that on my truck. Sent from my iPhone- STecoD
- Post #1,627
- Forum: 4th Gen DIY
-
AlfaOBD
I can confirm the 3.5 works. Sent from my iPhone using Tapatalk- STecoD
- Post #7,190
- Forum: 4th Gen DIY
-
How to add power inverter 2017+ Ram
You asked for i310 not i320. Here is i320 Sent from my iPhone using Tapatalk- STecoD
- Post #61
- Forum: 4th Gen DIY
Latest posts
-
Intermittent power steering problem at slow speed or stopped.- Latest: Harley Harrold
-
-
-
