Recent content by Yoox_II

  1. Y

    Door Adjustment?

    Just installed new fenders. Passenger side went on great but driver's side is giving me trouble. I've figured out what's not lining up - the driver's side door is too far forward, against the fender. All other body panels are lined up .There are many signs that the door needs to move back...
  2. Y

    Can You Paint an ECU/ECM?

    Hello I'm installing new fenders on my truck. I have a computer mounted to the inside of the fender to run my 5.7l hemi. I will obviously be transferring the ecm over to the new fender. My question is - can I paint/coat the ecm? I believe it's made with an aluminum casing, which is showing...
  3. Y

    Severe Driveline Vibration

    Trying to locate the source of a bad vibration at certain speeds, around 100km/h. It's only present when I let off the throttle at that speed, goes away when I'm on the throttle. The vibration can also be felt for a second when I apply throttle at slower speeds, almost in sync with when the...
  4. Y

    Need Help - Rear Brake Job

    I've unfortunately confirmed that I have 8.75 backing plates. Can anyone confirm or deny that they will be compatible with my 8.25 rear end/axles? Specifically concerned about the axle bolt pattern.
  5. Y

    Need Help - Rear Brake Job

    Thanks crazy wolf. You always have the answers. This is a pic of the backing plates I have. Ive mentioned before I have a 8.25 Chrysler rear end. These plates I have appear to have an extra bolt hole compared to the ones on my truck. It's the bolt hole directly under where the axle goes thru...
  6. Y

    Need Help - Rear Brake Job

    Thank you for the assistance guys .I am currently assembling the shoes and hardware onto the plates on the bench tonight .I have them assembled but have one question. There is a metal "arm" that indexes into the horizontal retaining arm. I don't know where it attached on the bottom section of...
  7. Y

    Need Help - Rear Brake Job

    I'm aware of removing the diff cover to access the c clip. My concern is, is there a way to F it up? For example is there a chance the c clip won't index properly if I install it wrong during reassembly
  8. Y

    Need Help - Rear Brake Job

    Is there a how-to thread or article I can read on replacing the backing plates on a 8.25 rear end? I will be doing it myself and wouldn't mind a few pointers. I can't seem to find anything except for drum & shoe replacement (which doesn't require removal of the axles)
  9. Y

    Need Help - Rear Brake Job

    I kept the stock 727 trans. It only required a different flexplate to mate it to the hemi. I had somewhat of a build thread when I did it about a year and a half ago. I can't locate it right now for some reason .
  10. Y

    Need Help - Rear Brake Job

    I'm going to be replacing my rear brakes this week. Drums, shoes, hardware, and backing plates .I understand that I need to take the axles out to replace the backing plates. Is there any additional parts I should have ready? Do the axle seals get disturbed during the tear down? Any other special...
  11. Y

    Any WeatherTech-like Floor Mats?

    I will be applying POR15 to the bare steel floor then laying Dynomat and then laying the carpet. I'm looking for high sided floor mats that go ontop of the carpet. The only mats I find are the standard flat ones that lets water run right off of them
  12. Y

    Any WeatherTech-like Floor Mats?

    I'm about to replace the carpet in my truck. It has been down all winter while I get it prepped and repairing some long overdue problems. Obviously weathertech doesn't make mats for first gen dodge trucks - are there any brands out there that make an all weather, high sided, molded floor mat...
  13. Y

    Looking for transmission mount

    I'm trying to get a line on an NOS molar one but they're hard to come by.
  14. Y

    Looking for transmission mount

    I found a part number for the mount, but I cannot find it available anywhere. Supposedly the product number is 4494475 but anyone who lists it says it's no longer available. Any other options?
  15. Y

    Looking for transmission mount

    I need to replace the transmission mount near the rear of the transmission. Is it sold as a full cross member piece or can I just replace the mount (is it bolt on?)? 84 d150 with 727 .
See more

Latest posts

Members online

Total: 775 (members: 19, guests: 756)
Robots: 1,280

Forum statistics

Threads
195,652
Posts
2,872,933
Members
156,490
Latest member
OasisNinjaBat

Share this page

Top